正文文本
StorCLI
Reference Manual
January 2013
53419-00, Rev. F
StorCLI Reference Manual
January 2013
Revision History
Version and Date Description of Changes
Rev. F, January 2013 Added the pi and preventpiimport options to Table 4.
Added a note and a caution message at the start of Chapter 4, Working with the Storage Command
Line Tool.
Added a note in Section 4.3.9, Drive Secure Erase Commands.
Updated Section 4.4.2, Delete Virtual Drives Commands, for using the force option.
Added Section 4.4.7, Virtual Drive Erase Commands.
Updated Section 4.4.6, Virtual Drive Initialization Commands, for using the force option.
Added the storcli /cx/bbu show modes command in Section 4.9, BBU Commands.
Added Section 4.2.7, Controller Cache Command.
NOTE This Revision History lists only the changes made to the current version of the document. For a complete list of all revisions made to the
previous versions of this document since its original publication, see Appendix D, Revision Information.
LSI, the LSI & Design logo, CacheCade, Dimmer Switch, and MegaRAID are registered trademarks of LSI Corporation or its subsidiaries. All other brand and product names may be trademarks of their
respective companies.
LSI Corporation reserves the right to make changes to the product(s) or information disclosed herein at any time without notice. LSI Corporation does not assume any responsibility or liability arising out of
the application or use of any product or service described herein, except as expressly agreed to in writing by LSI Corporation; nor does the purchase, lease, or use of a product or service from LSI Corporation
convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual property rights of LSI Corporation or of third parties. LSI products are not intended for use in life-support
appliances, devices, or systems. Use of any LSI product in such applications without written consent of the appropriate LSI officer is prohibited.
Corporate Headquarters Email Website
San Jose, CA globalsupport@lsi.com www.lsi.com
800-372-2447
Document Number: 53419-00, Rev. F
Copyright © 2013 LSI Corporation
All Rights Reserved
StorCLI Reference Manual Table of Contents
January 2013
Table of Contents
Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Support for MegaCLI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3 Devices Supported by the StorCLI Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2: Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Installing StorCLI on Microsoft Windows Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Installing StorCLI on Linux Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Installing StorCLI on VMware Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4 Installing StorCLI on FreeBSD Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.5 Installing StorCLI on the Microsoft EFI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.6 Installing StorCLI on Solaris Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 3: StorCLI Command Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 4: Working with the Storage Command Line Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 System Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1.1 System Show Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2 Controller Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2.1 Show and Set Controller Properties Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2.2 Controller Show Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.2.3 Controller Background Tasks Operation Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.2.4 Premium Feature Key Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.2.5 Controller Security Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.2.6 Flashing Controller Firmware Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2.7 Controller Cache Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.3 Drive Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.3.1 Drive Show Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.3.2 Missing Drives Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.3.3 Set Drive State Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.3.4 Drive Initialization Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.3.5 Drive Firmware Download Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.3.6 Locate Drives Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.3.7 Prepare to Remove Drives Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.3.8 Drive Security Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.3.9 Drive Secure Erase Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.3.10 Rebuild Drives Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.3.11 Drive Copyback Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.3.12 Hot Spare Drive Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.3.13 Drive Security Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.4 Virtual Drives Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.4.1 Add Virtual Drives Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.4.2 Delete Virtual Drives Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.4.3 Virtual Drive Show Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.4.4 Preserved Cache Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.4.5 Change Virtual Drive Properties Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.4.6 Virtual Drive Initialization Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.4.7 Virtual Drive Erase Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.4.8 Virtual Drive Migration Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
LSI Corporation
- 3 -
StorCLI Reference Manual Table of Contents
January 2013
4.4.9 Virtual Drive Consistency Check Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.4.10 Background Initialization Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.4.11 Virtual Drive Expansion Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.5 Foreign Configurations Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.6 BIOS-Related Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.6.1 OPROM BIOS Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.7 Drive Group Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.7.1 Drive Group Show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.8 Dimmer Switch Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.8.1 Change Virtual Drive Power Settings Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.9 BBU Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.10 Enclosure Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.11 PHY Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.12 Logging Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Chapter 5: Frequently Used Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.1 Showing the Version of the Storage Command Line Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.2 Showing StorCLI Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.3 Showing System Summary Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.4 Showing Free Space in a Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.5 Adding Virtual Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.6 Setting the Cache Policy in a Virtual Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
5.7 Showing Virtual Drive Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
5.8 Deleting Virtual Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
5.9 Flashing Controller Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Appendix A: 3Ware CLI Commands to StorCLI Command Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Appendix B: MegaCLI Commands to StorCLI Command Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Appendix C: Unsupported Commands in Embedded MegaRAID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Appendix D: Revision Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
LSI Corporation
- 4 -
StorCLI Reference Manual Chapter 1: Introduction
January 2013 Overview
Chapter 1: Introduction
1.1 Overview
The Storage Command Line Tool (StorCLI) is the command line management software designed for the MegaRAID®
product line. The StorCLI is a command line interface that is designed to be easy to use, consistent, and easy to script.
This document is the reference manual for installing and using the Storage Command Line Tool, and it explains the
various features of the Storage Command Line Tool.
NOTE The legacy commands are deprecated from this guide.
1.2 Support for MegaCLI Commands
The MegaCLI commands can be executed on the Storage Command Line (StorCLI) tool. A single binary is output for
the StorCLI commands and its equivalent MegaCLI commands. See Appendix B, MegaCLI Commands to StorCLI
Command Conversion, for the information for conversion from MegaCLI commands to StorCLI commands.
1.3 Devices Supported by the StorCLI Tool
The StorCLI tool is designed to work with the MegaRAID product line. The StorCLI tool supports the following
MegaRAID products.
The 926x product line.
The 928x product line.
The 924x product line.
LSI® MegaRAID SAS iMR
LSI MegaRAID SAS 9280-8e
LSI MegaRAID SAS 9260CV-8i
LSI MegaRAID SAS 9266CV-8i
LSI MegaRAID SAS 9285-8e
LSI Corporation
- 5 -
StorCLI Reference Manual Chapter 2: Installation
January 2013 Installing StorCLI on Microsoft Windows Operating Systems
Chapter 2: Installation
The MegaRAID controllers can be used with the following operating systems for Intel and AMD 32-bit and 64-bit
x86-based motherboards:
Microsoft® Windows® Server 2008 R2
Microsoft Windows 7 (32/64 bit)
Red Hat® Enterprise Linux® 5.8 (32/64 bit)
Red Hat Enterprise Linux 6.1
Red Hat Enterprise Linux 6.2 (32/64 bit)
SUSE® Linux Enterprise Server 11 SP2 (32/64 bit)
SUSE Linux Enterprise Server 10 SP4 (32/64 bit)
Fedora Core Linux 15
VMware® ESX 4.0
VMware ESX 4.1 U2
VMware ESXi 4.1 U2
VMware ESXi 5.0 U1
Solaris
FreeBSD
EFI
NOTE The LSISAS2208 and LSISAS2108 controllers provide support for Microsoft Windows 8 and Microsoft
Windows Server 2012 operating systems.
2.1 Installing StorCLI on Microsoft Windows Operating Systems
The Windows StorCLI binary is provided in a binary format, and no separate installation is required.
1. Copy the binary file from the CD or from the LSI website.
2. Place the binary file in the directory from which you want to run the Storage Command Line Tool, and run
the tool.
NOTE StorCLI must be run with the administrator privileges.
2.2 Installing StorCLI on Linux Operating Systems
To install StorCLI on Linux operating systems, perform the following steps:
1. Unzip the StorCLI package.
2. To install the StorCLI RPM, run the rpm -ivh <StorCLI-x.xx-x.noarch.rpm> command.
3. To upgrade the StorCLI RPM, run the rpm -Uvh <StorCLI-x.xx-x.noarch.rpm> command.
LSI Corporation
- 6 -
StorCLI Reference Manual Chapter 2: Installation
January 2013 Installing StorCLI on VMware Operating Systems
2.3 Installing StorCLI on VMware Operating Systems
To install StorCLI on VMware operating systems, run the following syntax from the command line:
esxcli software vib install –v=<path-to-vib-package>
Example:
esxcli software vib install
-v=/vmfs/volumes/datastore1/StorCliMN/vmware-esx-StorCli-1.01.04.vib
2.4 Installing StorCLI on FreeBSD Operating Systems
The FreeBSD StorCLI binary is provided in a binary format, and no separate installation is required.
1. Copy the binary file from the CD or from the LSI website.
2. Place the binary file in the directory from which you want to run the Storage Command Line Tool, and run
the tool.
2.5 Installing StorCLI on the Microsoft EFI
The EFI StorCLI binary is provided in a binary format, and no separate installation is required.
1. Copy the binary file from the CD or from the LSI website.
2. Place the binary file in the directory from which you want to run the Storage Command Line Tool, and run
the tool.
2.6 Installing StorCLI on Solaris Operating Systems
To install StorCLI on Solaris operating systems, run the following command:
pkgadd –d Storcli.pkg
LSI Corporation
- 7 -
StorCLI Reference Manual Chapter 3: StorCLI Command Syntax
January 2013
Chapter 3: StorCLI Command Syntax
This chapter describes the StorCLI command syntax and the valid values for each parameter in the general
command syntax.
NOTE To get the output in JSON format, add J at the end of the command syntax.
Example: storcli /cx show <property1>|<property2> J.
NOTE JSON format output is not supported in the EFI operating system. The EFI platform ignores the J when it is
added at the end of the command syntax.
NOTE Background operations are blocked in the EFI and HII environments and these operations are resumed in the
operating system environments.
The StorCLI syntax uses the following general format:
<[object identifier]> <verb> <[adverb | attributes | properties] > <[key=value]>
The StorCLI tool supports the object identifiers listed in the following table.
Table 1 Object Identifiers in the StorCli Command Syntax
Object Identifier Description
No object identifier specified If there is no object identifier, the command is a system command.
/cx This object identifier is for controller x.
/cx/vx This object identifier is for a virtual drive x on controller x.
/cx/vall This object identifier is for all virtual drives on controller x.
/cx/ex This object identifier is for an enclosure x on controller x.
/cx/eall This object identifier is for all enclosures on controller x.
/cx/fx This object identifier is for a foreign configuration x on controller x.
/cx/fall This object identifier is for all foreign configurations on controller x.
/cx/ex/sx This object identifier is for the drive is slot x on enclosure x on controller x.
/cx/sx This object identifier represents the drives that are directly attached to controller x.
/cx/ex/sall This object identifier is for all the drives on enclosure x on controller x.
/cx/dx This object identifier is for the drive group x on enclosure x on controller x.
/cx/dall This object identifier is for the all drive groups on enclosure x on controller x.
NOTE If enclosures are not used to connect physical drives to the controller, you do not specify the enclosure
ID in the command.
LSI Corporation
- 8 -
StorCLI Reference Manual Chapter 3: StorCLI Command Syntax
January 2013
The StorCLI tool supports the following verbs.
Table 2 Verbs in the StorCli Command Syntax
Verbs Description
add This verb adds virtual drives, JBODs, and so on to the object identifier.
del This verb deletes a drive, value, or property of the object identifier.
set This verb sets a value of the object identifier.
show This verb shows the value and properties of the object identifier.
pause This verb pauses an ongoing operation.
resume This verb resumes paused operation.
suspend This verb suspends an ongoing operation. A suspended operation cannot be resumed.
compare This verb compares an input value with a system value.
download This verb downloads and flashes a file to the target.
start This verb starts an operation.
flush This verb flushes a controller cache or a drive cache.
stop This verb stops an operation that is in progress. A stopped process cannot be resumed.
import This verb imports the foreign configuration into the drive.
expand This verb expands the size of the virtual drive.
<[adverb | attributes | properties] > – Specifies what the verb modifies or displays.
<[key=value]> – Specifies a value, if a value is required by the command.
LSI Corporation
- 9 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 System Commands
Chapter 4: Working with the Storage Command Line Tool
This chapter describes the commands supported by the Storage Command Line Tool.
NOTE The Storage Command Line Tool is not case sensitive.
CAUTION The order in which you specify the command options should be the same as in the User Guide;
otherwise, the command will fail.
NOTE The Storage Command Line Tool does not support the Snapshot feature.
4.1 System Commands
4.1.1 System Show Commands
The Storage Command Line Tool supports the following system show commands:
storcli show
storcli show all
storcli show ctrlcount
storcli show help
storcli -v
The detailed description for each command follows.
storcli show
This command shows a summary of controller and controller-associated information for the system. The summary
includes the number of controllers, the host name, the operating system information, and the overview of
existing configuration.
storcli show all
This command shows the list of controllers and controller-associated information, information about the drives that
need attention, and advanced software options.
storcli show ctrlcount
This command shows the number of controllers detected in the server.
storcli show help
This command shows help for all commands at the server level.
storcli -v
This command shows the version of the Storage Command Line Tool.
LSI Corporation
- 10 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Controller Commands
4.2 Controller Commands
Controller commands provide information and perform actions related to the specified controller, such as the /c0
controller. The Storage Command Line Tool supports the controller commands described in this section.
4.2.1 Show and Set Controller Properties Commands
Table 3 Controller Commands Quick Reference Table
Commands Value Range Description
show <properties> See Table 4 Shows specific controller properties.
set <properties> See Table 4 Sets controller properties.
show all: Shows all properties of the virtual drive. Shows physical drive information.
freespace: Shows the freespace in the controller.
See Section 4.2.2, Controller Show Commands.
This section provides command information to show and set controller properties.
NOTE You cannot set multiple properties with a single command.
The generalized syntax for show controller properties command is as follows.
storcli /cx show <property>
This command shows the current value of the specified property on the specified controller.
General example output:
Status Code = 0
Status = Success
Description = None
Controller: 0
Property_name = Property_value
You can show the following properties using the storcli /cx show <property1>|<property2>
command.
storcli /cx show abortcconerror
storcli /cx show activityforlocate
storcli /cx show alarm
storcli /cx show backplane
storcli /cx show batterywarning
storcli /cx show bgirate
storcli /cx show bootwithpinnedcache
storcli /cx show cachebypass
storcli /cx show cacheflushint
storcli /cx show ccrate
storcli /cx show clusterenable
storcli /cx show coercion
storcli /cx show consistencycheck|cc
storcli /cx show copyback
storcli /cx show directpdmapping
storcli /cx show dimmerswitch|ds
LSI Corporation
- 11 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Controller Commands
storcli /cx show eccbucketleakrate
storcli /cx show eccbucketsize
storcli /cx show enableeghsp
storcli /cx show enableesmarter
storcli /cx show enableeug
storcli /cx show exposeencldevice
storcli /cx show jbod
storcli /cx show loadbalancemode
storcli /cx show maintainpdfailhistory
storcli /cx show migraterate
storcli /cx show ncq
storcli /cx show patrolread|pr
storcli /cx show perfmode
storcli /cx show pi
storcli /cx show preventpiimport
storcli /cx show prcorrectunconfiguredareas
storcli /cx show prrate
storcli /cx show rebuildrate
storcli /cx show rehostinfo
storcli /cx show restorehotspare
storcli /cx show safeid
storcli /cx show smartpollinterval
storcli /cx show spinupdelay
storcli /cx show spinupdrivecount
storcli /cx show time
storcli /cx show usefdeonlyencrypt
storcli /cx show memscrubpatterns
storcli /cx show badblocks
storcli /cx(x|all) show PI
storcli /cx(x|all) show preventpiimport
storcli /cx set <property>=<value>
General example output:
Status Code = 0
Status = Success
Description = None
Controller 0, new Property_name = Property_value
The following commands are examples of the properties that can be set using the storcli /cx set
<property>=<value> command:
storcli /cx set abortcconerror=<on|off>
storcli /cx set termlog[=on|off|offthisboot]
storcli /cx set activityforlocate=<on|off>
storcli /cx set alarm=<on|off|silence>
storcli /cx set backplane=<value>
storcli /cx set batterywarning=<on|off>
storcli /cx set bgirate=<value>
storcli /cx set bootwithpinnedcache=<on|off>
storcli /cx set cachebypass=<on|off>
storcli /cx set cacheflushinterval=<value>
storcli /cx set ccrate=<value>
storcli /cx set coercion=<value>
LSI Corporation
- 12 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Controller Commands
storcli /cx set consistencycheck|cc=[off|seq|conc][delay=value]
[starttime=yyyy/mm/dd hh] [excludevd=x-y,z]
storcli /cx set clusterenable=<value>
storcli /cx set copyback=<on|off> type=<smartssd|smarthdd|all>
storcli /cx set directpdmapping=<on|off>
storcli /cx set eccbucketleakrate=<value>
storcli /cx set eccbucketsize=<value>
storcli /cx set enableeghsp=<on|off>
storcli /cx set enableesmarter=<value>
storcli /cx set enableeug=<on|off>
storcli /cx set exposeencldevice=<on|off>
storcli /cx set dimmerswitch|ds=<on|off type=1|2|3|4>
storcli /cx set foreignautoimport=<on|off>
storcli /cx set jbod=<on|off>
storcli /cx set loadbalancemode=<value>
storcli /cx set maintainpdfailhistory=<on|off>
storcli /cx set migraterate=<value>
storcli /cx set ncq=<on|off>
storcli /cx set patrolread|pr {=on mode=<auto|manual>}|{off}
storcli /cx set perfmode=<value>
storcli /cx set pi=<on|off>
storcli /cx set preventpiimport=<on|off>
storcli /cx set prcorrectunconfiguredareas=<on|off>
storcli /cx set prrate=<value>
storcli /cx set rebuildrate=<value>
storcli /cx set restorehotspare=<on|off>
storcli /cx set smartpollinterval=<value>
storcli /cx set spinupdelay=<value>
storcli /cx set spinupdrivecount=<value>
storcli /cx set stoponerror=<on|off>
storcli /cx set usefdeonlyencrypt=<on|off>
storcli /cx set time=yyyymmdd hh:mm:ss|systemtime
storcli /cx set usefdeonlyencrypt=<on|off>
The following table lists and describes the properties for the show and set commands.
Table 4 Properties for Show and Set Commands
Property Name Set Command Range Description
abortcconerror on|off Aborts consistency check when it detects an
inconsistency.
activityforlocate on|off Enables/disables drive activity, drive activity locates
function for systems without SGPIO/SES capabilities.
alarm on|off|silence Enables/disables alarm on critical errors.
silence: Silences the alarm.
backplane 0: Use autodetect logic of backplanes, Configures enclosure detection on a non-SES/expander
such as SGPIO and I2C SEP using GPIO backplane.
pins.
1: Disable autodetect SGPIO.
2: Disable I2C SEP autodetect.
3: Disable both the autodetects.
batterywarning on|off Enables/disables battery warnings.
bgirate 0 to 100 Sets background initialization rate in percentage.
LSI Corporation
- 13 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Controller Commands
Table 4 Properties for Show and Set Commands (Continued)
Property Name Set Command Range Description
cacheflushint 0 to 255, default value 4 Sets cache flush interval in seconds.
ccrate 0 to 100 Sets consistency check rate in percentage.
coercion 0: No coercion Sets drive capacity in coercion mode.
1: 128 MB
2: 1 GB
consistencycheck See Section 4.2.3.3, Consistency Check. See Section 4.2.3.3, Consistency Check.
copyback on|off Enables/disables copy back for drive types.
type = smartssd|smarthdd|all
smartssd: Copy back enabled for SSD
drives.
smarthdd: Copy back enabled for HDD
drives.
all: Copy back enabled for both ssd
drives and HDD drives.
Example:
storcli /cx set copyback=on
type=all
directpdmapping on|off Enables/disables direct physical drive mapping. When
enclosures are used, this feature is disabled; otherwise it
should be enabled.
eccbucketleakrate 0 to 65535 Sets leak rate of the single-bit bucket in minutes (one
entry removed per leak-rate).
eccbucketsize 0 to 255 Sets size of ECC single-bit-error bucket (logs event
when full).
enableeghsp on|off Enables/disables the commissioning of otherwise
incompatible global hot spare drives as Emergency Hot
Spare (EHSP) drives.
enableesmarter on|off Enables/disables the commissioning of Emergency Hot
Spare (EHSP) drives for Predictive Failure (PFA) events.
enableeug on|off Enables/disables the commissioning of Unconfigured
Good drives as Emergency Hot Spare (EHSP) drives.
exposeencldevice on|off Enables/disables device drivers to expose enclosure
devices; for example, expanders, SEPs.
dimmerswitch|ds See Section 4.8, Dimmer Switch See Section 4.8, Dimmer Switch Commands.
Commands.
foreignautoimport on|off Imports foreign configuration automatically, at boot.
jbod on|off Enables/disables JBOD mode; by default, drives become
system drives.
NOTE Not supported by all controllers.
loadbalancemode on|off Enables/disables automatic load balancing between SAS
phys or ports in a wide port configuration.
maintainpdfailhistory on|off Maintains the physical drive fail history.
migraterate 0 to 100 Sets data migration rate in percentage.
patrolread|pr See Section 4.2.3.2, Patrol Read. See Section 4.2.3.2, Patrol Read.
LSI Corporation
- 14 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Controller Commands
Table 4 Properties for Show and Set Commands (Continued)
Property Name Set Command Range Description
perfmode 0: Tuned to provide best IOPS, currently Performance tuning setting for the controller.
applicable to non-FastPath
1: Tuned to provide least latency, currently
applicable to non-FastPath
pi on|off Enables/disables data protection on the controller.
preventpiimport on|off Enables/disables import data protection drives on
the controller.
prcorrectunconfiguredareas on|off Correct media errors during PR by writing 0s to
unconfigured areas of the disk.
prrate 0 to 100 Sets patrol read rate of the virtual drives in percentage.
rebuildrate 0 to 100 Sets rebuild rate of the drive in percentage.
reconrate 0 to 100 Sets reconstruction rate for a drive in percentage.
restorehotspare on|off Becomes a hot spare on insertion of a failed drive.
smartpollinterval 0 to 65535 Set time for polling of SMART errors in seconds.
spinupdrivecount 0 to 255 Sets number of drives that are spun up at a time.
spinupdelay 0 to 255 Sets spin-up delay between a group of drives or a set of
drives, in seconds.
stoponerror on|off Stops the MegaRAID BIOS during POST, if any errors are
encountered.
time Valid time in yymmdd hh:mm:ss format or Sets the controller time to your input value or the system
systemtime time (local time in 24-hour format).
usefdeonlyencrypt on|off Enables/disables FDE drive-based encryption.
4.2.2 Controller Show Commands
The Storage Command Line Tool supports the following show commands:
storcli /cx show
storcli /cx show all
storcli /cx show freespace
The detailed description for each command follows.
storcli /cx show
This command shows the summary of the controller information. The summary includes basic controller information,
foreign configurations, drive groups, virtual drives, physical drives, enclosures, and BBU information.
Input example:
storcli /c1 show
LSI Corporation
- 15 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Controller Commands
storcli /cx show all
This command shows all controller information, which includes basic controller information, bus information,
controller status, advanced software options, controller policies, controller defaults, controller capabilities, scheduled
tasks, miscellaneous properties, foreign configurations, drive groups, virtual drives, physical drives, enclosures, and
BBU information.
Input example:
storcli /c0 show all
NOTE The PCI information displayed as a part of storcli /cx show and storcli /cx show all
commands is not applicable for the FreeBSD operating system. Hence, the PCI information fields are displayed
as N/A.
storcli /cx show freespace
This command shows the usable free space in the controller.
Input example:
storcli /c0 show freespace
4.2.3 Controller Background Tasks Operation Commands
4.2.3.1 Rebuild Rate
storcli /cx set rebuildrate=<value>
storcli /cx show rebuildrate
The detailed description for each command follows.
storcli /cx set rebuildrate=<value>
This command sets the rebuild task rate of the specified controller. The input value is in percentage.
Input example:
storcli /c0 set rebuildrate=30
NOTE A high rebuild rate slows down I/O processing.
storcli /cx show rebuildrate
This command shows the current rebuild task rate of the specified controller in percentage.
Input example:
storcli /c0 show rebuildrate
LSI Corporation
- 16 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Controller Commands
4.2.3.2 Patrol Read
The Storage Command Line Tool supports the following patrol read commands:
storcli /cx resume patrolread
storcli /cx set patrolread ={{on mode=<auto|manual>}|{off}}
storcli /cx set patrolread [starttime=<yyyy/mm/dd hh>] [maxconcurrentpd=<value>]
[includessds=<on|off>] [uncfgareas=<on|off>]
storcli /cx set patrolread delay=<value>
storcli /cx show patrolread
storcli /cx start patrolread
storcli /cx stop patrolread
storcli /cx suspend patrolread
NOTE A patrol read operation is scheduled for all the physical drives of the controller.
The detailed description for each command follows.
storcli /cx resume patrolread
This command resumes a suspended patrol read operation.
Input example:
storcli /c0 resume patrolread
storcli /cx set patrolread {=on mode=<auto|manual>}|{off}
This command turns the patrol read scheduling on and sets the mode of the patrol read to automatic or manual.
Input example:
storcli /co set patrolread=on mode=manual
storcli /cx set patrolread [starttime=<yyyy/mm/dd hh>] [maxconcurrentpd=<value>] [includessds=<on|off>]
[uncfgareas=on|off]
This command schedules a patrol read operation. You can use the following options for patrol read command.
Table 5 Set Patrolread Input Options
Option Value Range Description
starttime A valid date and hour in 24 hours format Sets the start time in yyyy/mm/dd hh format.
maxconcurrentpd Valid number of physical drives present Sets the number of physical drives that can be patrol read at a
single time.
includessds — Include SSDs in the patrol read.
uncfgareas — Include the areas not configured in the patrol read.
NOTE Controller time is taken as a reference for scheduling a patrol read operation.
Input example:
storcli /c0 set patrolread=on starttime=2012/02/21 00
LSI Corporation
- 17 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Controller Commands
storcli /cx set patrolread [delay=<value>]
This command delays the scheduled patrol read in hours.
Input example:
storcli /c0 set patrolread delay=30
storcli /cx show patrolRead
This command shows the progress on the current patrol read in percentage.
Input example:
storcli /c0 show patrolread
storcli /cx start patrolread
This command starts the patrol read operation. This command starts a patrol read immediately.
Input example:
storcli /c0 start patrolread
storcli /cx stop patrolread
This command stops a running patrol read operation.
Input example:
storcli /c0 stop patrolread
NOTE You cannot resume a stopped patrol read.
storcli /cx suspend patrolread
This command pauses a running patrol read operation.
Input example:
storcli /c0 suspend patrolread
NOTE You can run this command only when a patrol read operation is running on the controller.
4.2.3.3 Consistency Check
The Storage Command Line Tool supports the following commands to schedule, perform, and view the status of a
consistency check (CC) operation:
storcli /cx set consistencycheck|cc=[off|seq|conc][delay=value]
starttime=yyyy/mm/dd hh [excludevd=x-y,z]
storcli /cx show cc
storcli /cx show ccrate
The detailed description for each command follows.
LSI Corporation
- 18 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Controller Commands
storcli /cx set consistencycheck|cc=[off|seq|conc][delay=value] starttime=yyyy/mm/dd hh [excludevd=x-y,z]
This command schedules a consistency check (CC) operation. You can use the following options with the consistency
check command.
Table 6 Set CC Input Options
Option Value Range Description
cc seq: Sequential mode. Sets CC to either sequential mode, or concurrent mode, or turns off the CC.
conc: Concurrent mode.
NOTE The concurrent mode slows I/O processing.
off: Turns off the consistency check
delay -1 and any integer value. Delay a scheduled consistency check. The value is in hours. A value of 0 makes
the CC runs continuously with no delay (in a loop).
NOTE Only scheduled consistency checks can be delayed.
starttime A valid date and hour in 24-hours Start time of a consistency check is yyyy/mm/dd hh format.
format.
excludevd The range should be less than the Excludes virtual drives from the consistency checks. To exclude particular virtual
number of virtual drives. drives, you can provide list of virtual drive names (Vx,Vy … format) or the range
of virtual drives that you want to exclude from a consistency check (Vx-Vy
format). If this option is not specified in the command, no virtual drives
are excluded.
Input example:
storcli /c0 set CC=on starttime=2012/02/21 00 excludevd v0-v3
storcli /cx show cc
This command shows the consistency check schedule properties for a controller.
Input example:
storcli /c0 show cc
storcli /cx show ccrate
This command checks the status of a consistency check operation. The CC rate appears in percentage.
Input example:
storcli /c0 show ccrate
NOTE A high CC rate slows I/O processing.
4.2.4 Premium Feature Key Commands
The Storage Command Line Tool supports the following commands for premium feature keys:
storcli /cx set advancedsoftwareoptions(aso) key=<value> [preview] |
[deactivatetrialkey] [rehostcomplete]
storcli /cx show safeid
The detailed description for the command follows.
LSI Corporation
- 19 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Controller Commands
storcli /cx set advancedsoftwareoptions(aso) key=<value> [preview] | [deactivatetrialkey]
[rehostcomplete][transfertovault]
This command activates advanced software options (ASO) for a controller. You can use the following options with the
advanced software options command.
Table 7 Set Advanced Software Options Input Options
Option Value Range Description
key 40 alpha numeric characters. Key to activate ASO on the controller.
NOTE After they are activated, ASOs cannot be removed from the controller.
deactivatetrialkey — Deactivates the trial key applied on the specified controller.
rehostcomplete — Enables rehosting on the specified controller.
transfertovault — Transfers the ASO key to the vault and disables the ASO.
Input example:
storcli /c0 set Aso key=LSI0000
storcli /cx show safeid
This command shows the Safe ID of the specified controller.
Input example:
storcli /c0 show safeid
4.2.5 Controller Security Commands
The Storage Command Line Tool supports the following controller security commands:
storcli /cx compare securitykey=ssssss
storcli /cx delete securitykey
storcli /cx set securitykey keyid=kkkk
storcli /cx set securitykey=sssss [passphrase=sssss][keyid=sssss]
storcli /cx set securitykey=sssss oldsecuritykey=ssss [passphrase=sssss]
[keyid=sssss]
The detailed description for each command follows.
storcli /cx compare securitykey=ssssss
This command compares and verifies the security key of the controller.
storcli /cx delete securitykey
This command deletes the security key of the controller.
Input example:
storcli /c0 delete securitykey
storcli /cx set securitykey keyId=kkkk
This command sets the key ID for the controller. The key ID is unique for every controller.
LSI Corporation
- 20 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Controller Commands
storcli /cx set securitykey=sssss [passphrase=sssss][keyid=sssss]
This command sets the security key for the controller. You can use the following options with the set security
key command.
Table 8 Set Security Key Input Options
Option Value Range Description
passphrase Should have a combination of numbers, upper String that is linked to the controller and is used in the next bootup to
case letters, lower case letters and special encrypt the lock key. If the passphrase is not set, the controller
characters. generates it by default.
Minimum of 8 characters and maximum of
32 characters.
keyid — Unique ID set for different controllers to help you specify a passphrase
to a specific controller.
Input example:
storcli /c0 set securitykey=Lsi@12345 passphrase=Lsi@123456 keyid=1
storcli /cx set securitykey=sssss oldsecuritykey=ssss [passphrase=sssss][keyid=sssss]
This command changes the security key for the controller.
Input example:
storcli /c0 set securitykey=Lsi@12345 oldsecuritykey=pass123
passphrase=Lsi@123456 keyid=1
4.2.6 Flashing Controller Firmware Command
NOTE The Flashing Controller Firmware command is not supported in Embedded MegaRAID.
The following command flash the controller firmware.
storcli /cx download file=filepath [fwtype=<value>] [nosigchk] [noverchk] [resetnow]
This command flashes the firmware to the specified adapter from the given file location (filepath is the absolute
file path). You can use the following options when you flash the firmware:
Table 9 Flashing Controller Firmware Input Options
Option Value Range Description
nosigchk — The application flashes the firmware even if the check word on the file does not match the required
check word for the controller.
NOTE You can damage the controller if a corrupted image is flashed using this option.
noverchk — The application flashes the controller firmware without checking the version of the firmware image.
fwtype 0: Application The firmware type to be downloaded. The application downloads the firmware for the controller. The
TMMC downloads the firmware for the TMMC battery only. Default is 0 (application). 1: TMMC
resetnow Invokes online firmware update on the controller; you do not need to reboot the controller to make
the update effective.
LSI Corporation
- 21 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Drive Commands
4.2.7 Controller Cache Command
The following command flushes the controller cache:
storcli /cx flush|flushcache
This command flushes the controller cache.
Input example:
storcli /c0 flushcache
4.3 Drive Commands
This section describes the drive commands, which provide information and perform actions related to physical drives.
The following table describes frequently used virtual drive commands.
Table 10 Physical Drives Commands Quick Reference Table
Commands Value Range Description
set missing: Sets the drive status as missing. Sets physical drive properties.
good: Sets the drive status to unconfigured good.
offline: Sets the drive status to offline.
online: Sets the drive status to online.
show all: shows all properties of the physical drive. Shows virtual drive information.
See Section 4.3.1, Drive Show Commands.
4.3.1 Drive Show Commands
The Storage Command Line Tool supports the following drive show commands:
storcli /cx[/ex]/sx show
storcli /cx[/eall]/sall show
storcli /cx[/ex]/sx|sall show all
NOTE If enclosures are used to connect physical drives to the controller, specify the enclosure ID in the
command. If no enclosures are used, you must specify the controller ID and slot ID.
The detailed description for each command follows.
storcli /cx[/ex]/sx show
This command shows the summary of the physical drive for a specified slot in the controller.
Input example:
storcli /c0/e0/s4,5 show
storcli /cx[/eall]/sall show
This command shows the summary information for all the enclosures and physical drives connected to the controller.
Input example:
storcli /c0/eall/sall show
LSI Corporation
- 22 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Drive Commands
storcli /cx[/ex]/sx|sall show all
This command shows all information of a physical drive for the specified slot in the controller. If you use the all
option, the command shows information for all slots on the controller. x stands for a number, a list of numbers, a range
of numbers, or all numbers.
Input examples:
storcli /c0/e3/s0-3 show all
storcli /c0/e35/sall show all
NOTE The storcli /cx/sx show all command shows tape drives information.
4.3.2 Missing Drives Commands
The Storage Command Line Tool supports the following commands to mark and replace missing physical drives:
storcli /cx[/ex]/sx insert array=a row=b
storcli /cx[/ex]/sx set missing
storcli /cx[/ex]/sx set offline
storcli /cx/dall
The detailed description for each command follows.
storcli /cx[/ex]/sx insert array=a row=b
This command replaces the configured drive that is identified as missing, and then starts an automatic rebuild.
Input example:
storcli /c0/e25/s3 insert array=2 row=1
storcli /cx[/ex]/sx set missing
This command marks a drive as missing.
Input example:
storcli /c0/s4 set missing
storcli /cx/dall
This command is used to find the missing drives.
storcli /cx[/ex]/sx set offline
This command marks the drive in an array as offline.
NOTE To set a drive that is part of an array as missing, first set it as offline. After the drive is set to offline, you
can then set the drive to missing.
4.3.3 Set Drive State Commands
The Storage Command Line Tool supports the following commands to set the status of physical drives:
storcli /cx[/ex]/sx set jbod
storcli /cx[/ex]/sx set good [force]
storcli /cx[/ex]/sx set offline
storcli /cx[/ex]/sx set online
LSI Corporation
- 23 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Drive Commands
The detailed description for each command follows.
storcli /cx[/ex]/sx set jbod
This command sets the drive state to JBOD.
Input example:
storcli /c1/e56/s3 set jbod
storcli /cx[/ex]/sx set good [force]
This drive changes the drive state to unconfigured good. If the drive has the operating system in it, use the
force option.
Input example:
storcli /c1/e56/s3 set good
storcli /cx[/ex]/sx set offline
This command changes the drive state to offline.
Input example:
storcli /c1/e56/s3 set offline
storcli /cx[/ex]/sx set online
This command changes the drive state to online.
Input example:
storcli /c1/e56/s3 set online
4.3.4 Drive Initialization Commands
When you initialize drives, all the data from the drives is cleared. The Storage Command Line Tool supports the
following commands to initialize drives:
storcli /cx[/ex]/sx show initialization
storcli /cx[/ex]/sx start initialization
storcli /cx[/ex]/sx stop initialization
The detailed description for each command follows.
storcli /cx[/ex]/sx show initialization
This command shows the current progress of the initialization progress in percentage.
Input example:
storcli /c0/e31/s4 show initialization
storcli /cx[/ex]/sx start initialization
This command starts the initialization process on a drive.
Input example:
storcli /c0/e31/s4 start initialization
LSI Corporation
- 24 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Drive Commands
storcli /cx[/ex]/sx stop initialization
This command stops an initialization process running on the specified drive. A stopped initialization process cannot
be resumed.
Input example:
storcli /c0/e56/s1 stop initialization
4.3.5 Drive Firmware Download Commands
The Storage Command Line Tool supports the following command to download drive firmware:
storcli /cx[/ex]/sx download src=filepath [satabridge]
This command flashes the firmware with the specified file. The satabridge option lets you download the SATA
bridge firmware in online mode.
Input example:
storcli /c0/e56/s1 download src=c:\file1.bin
4.3.6 Locate Drives Commands
The Storage Command Line Tool supports the following commands to locate a drive and activate the physical disk
activity LED:
storcli /cx[/ex]/sx start locate
storcli /cx[/ex]/sx stop locate
The detailed description for each command follows.
storcli /cx[/ex]/sx start locate
This command locates a drive and activates the drive’s LED.
Input example:
storcli /c0/e56/s1 start locate
storcli /cx[/ex]/sx stop locate
This command stops a locate operation and deactivates the drive’s LED.
Input example:
storcli /c0/e56/s1 stop locate
4.3.7 Prepare to Remove Drives Commands
The Storage CLI supports the following commands to prepare the physical drive for removal:
storcli /cx[/ex]/sx spindown
storcli /cx[/ex]/sx spinup
The detailed description for each command follows.
LSI Corporation
- 25 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Drive Commands
storcli /cx[/ex]/sx spindown
This command spins down an unconfigured drive and prepares it for removal. The drive state is unaffiliated and it is
marked offline.
Input example:
storcli /cx/e34/s4 spindown
storcli /cx[/ex]/sx spinup
This command spins up a spun-down drive and the drive state is unconfigured good.
Input example:
storcli /cx/e34/s4 spinup
4.3.8 Drive Security Commands
The Storage Command Line supports the following drive security command:
storcli /cx[/ex]/sx show securitykey keyid
This command shows the security key and key ID of the controller.
Input example:
storcli /c0/s4 show securityKey keyid
4.3.9 Drive Secure Erase Commands
The Storage Command Line supports the following drive erase commands:
storcli /cx[/ex]/sx secureerase [force]
storcli /cx[/ex]/sx start erase [simple|normal|thorough] [erasepatternA=<value1>]
[erasepatternB=<value2>]
storcli /cx[/ex]/sx stop erase
The detailed description for each command follows.
storcli /cx[/ex]/sx secureerase [force]
This command erases the drive's security configuration and securely erases data on a drive. You can use the force
option as a confirmation to erase the data on the drive and the security information.
Input example:
storcli /c0/e25/s1 secureerase
NOTE This command deletes data on the drive and the security configuration and this data is no longer
accessible. This command is used for SED drives only.
LSI Corporation
- 26 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Drive Commands
storcli /cx[/ex]/sx start erase [simple|normal|thorough] [erasepatternA=<val1>] [erasepatternB=<val2>]
This command securely erases non-SED drives. The drive is written with erase patterns to ensure that the data is
securely erased. You can use the following options with the start erase command:
Table 11 Drive Erase Command Options
Options Value Range Description
erase simple: Single pass, single pattern write Secure erase type.
normal: Three pass, three pattern write
thorough: Nine pass, repeats the normal write 3 times
erasepatternA 8-bit value Erase pattern A to overwrite the data.
erasepatternB 8-bit value Erase pattern B to overwrite the data.
Input example:
storcli /c0/e25/s1 start erase thorough erasepatternA=10010011
erasepatternB=11110000
4.3.10 Rebuild Drives Commands
The following commands rebuild drives in the Storage Command Line Tool:
storcli /cx[/ex]/sx pause rebuild
storcli /cx[/ex]/sx resume rebuild
storcli /cx[/ex]/sx show rebuild
storcli /cx[/ex]/sx start rebuild
storcli /cx[/ex]/sx stop rebuild
NOTE If enclosures are used to connect physical drives to the controller, specify the enclosure ID in
the command.
The detailed description for each command follows.
storcli /cx[/ex]/sx pause rebuild
This command pauses an ongoing rebuild process. You can run this command only for a drive that is currently rebuilt.
Input example:
storcli /c0/s4 pause rebuild
storcli /cx[/ex]/sx resume rebuild
This command resumes a paused rebuild process. You can run this command only when a paused rebuild process for
the drive exists.
Input example:
storcli /c0/s4 resume rebuild
storcli /cx[/ex]/sx show rebuild
This command shows the progress of the rebuild process in percentage.
Input example:
storcli /c0/s5 show rebuild
LSI Corporation
- 27 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Drive Commands
storcli /cx[/ex]/sx start rebuild
This command starts a rebuild operation for a drive.
Input example:
storcli /c0/s4 start rebuild
storcli /cx[/ex]/sx stop rebuild
This command stops a rebuild operation. You can run this command only for a drive that is currently rebuilt.
Input example:
storcli /c0/s4 stop rebuild
4.3.11 Drive Copyback Commands
The Storage Command Line Tool supports the following commands for drive copyback:
storcli /cx[/ex]/sx pause copyback
storcli /cx[/ex]/sx resume copyback
storcli /cx[/ex]/sx show copyback
storcli /cx[/ex]/sx start copyback target=eid:sid
storcli /cx[/ex]/sx stop copyback
The detailed description for each command follows.
NOTE In the copyback commands, cx[/ex]/sx indicates the source drive and eid:sid indicates the
target drive.
storcli /cx[/ex]/sx pause copyback
This command pauses a copyback operation. You can run this command only when there is a copyback
operation running.
Input example:
storcli /c0/e25/s4 pause copyback
storcli /cx[/ex]/sx resume copyback
This command resumes a paused copyback operation. You can run this command only when there is a paused
copyback process for the drive.
Input example:
storcli /c0/e25/s4 resume copyback
storcli /cx[/ex]/sx show copyback
This command shows the progress of the copyback operation in percentage.
Input example:
storcli /c0/e25/s4 show copyback
storcli /cx[/ex]/sx start copyback target=eid:sid
This command starts a copyback operation for a drive.
Input example:
storcli /c0/e25/s4 start copyback target=25:8
LSI Corporation
- 28 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Drive Commands
storcli /cx[/ex]/sx stop copyback
This command stops a copyback operation. You can run this command only on drives that have the copyback
operation running.
Input example:
storcli /c0/e25/s4 stop copyback
NOTE A stopped rebuild process cannot be resumed.
4.3.12 Hot Spare Drive Commands
The following commands create and delete hot spare drives:
storcli /cx[/ex]/sx add hotsparedrive
{dgs=<n|0,1,2...>}[enclaffinity][nonrevertible]
storcli /cx/[ex]/sx delete hotsparedrive
NOTE If enclosures are used to connect the physical drives to the controller, specify the enclosure ID in
the command.
The detailed description for each command follows.
storcli /cx[/ex]/sx add hotsparedrive [{dgs=<n|0,1,2...>}] [enclaffinity][nonrevertible]
This command creates a hot spare drive. You can use the following options to create a hot spare drive::
Table 12 Add Hotsparedrive Input Options
Option Value Range Description
dgs Valid drive group number Specifies the drive group to which the hot spare drive is
dedicated.
enclaffinity Valid enclosure number Specifies the enclosure with which the hot spare is
associated. If this option is specified, affinity is set; if it is
not specified, there is no affinity.
NOTE Affinity cannot be removed after it is set for a hot
spare drive.
nonrevertible — Sets the drive as a nonrevertible hot spare.
Input example:
storcli /c0/e3/s4,5 add hotsparedrive
This command sets the drives /c0/e3/s4,5 as Global Hot spare.
Input example:
storcli /c0/e3/s6,8 add hotsparedrive dgs=0,1
This command sets /c0/e3/s6,8 as Dedicated Hot spare for disk groups 0,1.
LSI Corporation
- 29 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Virtual Drives Commands
storcli /cx/[ex]/sx delete hotsparedrive
This command deletes a hot spare drive.
Input example:
storcli /c0/e3/s4,5 delete hotsparedrive
4.3.13 Drive Security Commands
The Storage Command Line Tool supports the following drive security command:
storcli /cx[/ex]/sx show securitykey keyid
storcli /cx[/ex]/sx show securitykey keyid
This command shows the security key for secured physical drives.
Input example:
storcli /c0/e252/s1 show SecurityKey keyid
4.4 Virtual Drives Commands
The Storage Command Line Tool supports the following virtual drive commands. The following table describes
frequently used virtual drive commands.
Table 13 Virtual Drives Commands Quick Reference Table
Commands Value Range Description
add See Table 14 and Table 15 Creates virtual drives.
delete cc or cachecade: Deletes CacheCade® virtual drives. Deletes a virtual drive.
force: Deletes the virtual drive where operating system is present.
set See Table 14, Table 15, and Section 4.4.5, Change Virtual Drive Properties Sets virtual drive properties.
Commands
show all: Shows all properties of the virtual drive. Shows virtual drive information.
cc: Shows properties of CacheCade virtual drives.
See Section 4.4.3, Virtual Drive Show Commands.
4.4.1 Add Virtual Drives Commands
The Storage Command Line Tool supports the following commands to add virtual drives:
storcli /cx add vd type=raid[0|1|5|6|10|50|60][Size=<VD1_Sz>,<VD2_Sz>,..|*all]
[name=<VDNAME1>,..] drives=e:s|e:s-x|e:s-x,y;e:s-x,y,z [PDperArray=x][SED]
[pdcache=on|off|*default][pi] [DimmerSwitch(ds)=default|automatic(auto)|
*none|maximum(max)|MaximumWithoutCaching(maxnocache)][cachevd]
[wt|*wb] [nora|*ra] [*direct|cached] [CachedBadBBU|*NoCachedBadBBU]
[Strip=<8|16|32|64|128|256|1024>] [AfterVd=X] [Spares = [e:]s|[e:]s-x|[e:]s-x,y]
[force]
LSI Corporation
- 30 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Virtual Drives Commands
storcli /cx add vd each type=raid0 [name=<VDNAME1>,..] [drives=e:s|e:s-x|e:s-x,y]
[SED] [pdcache=on|off|*default][pi] [DimmerSwitch(ds)=default|automatic(auto)|
*none|maximum(max)|MaximumWithoutCaching(maxnocache)] [wt|*wb] [nora|*ra]
[*direct|cached] [CachedBadBBU|*NoCachedBadBBU][Strip=<8|16|32|64|128|256|1024]
storcli /cx add VD cachecade|cc Type = raid[0,1,10] drives =
[e:]s|[e:]s-x|[e:]s-x,y [WT| WB] [assignvds = 0,1,2
This command creates a RAID configuration. You can use the following options to create the RAID volume:
NOTE * indicates default values.
The detailed description for each command follows.
storcli /cx add vd type=raid[0|1|5|6|10|50|60][Size=<VD1_Sz>,<VD2_Sz>,..|*all] [name=<VDNAME1>,..]
drives=e:s|e:s-x|e:s-x,y;e:s-x,y,z [PDperArray=x][SED] [pdcache=on|off|*default][pi]
[DimmerSwitch(ds)=default|automatic(auto)|
*none|maximum(max)|MaximumWithoutCaching(maxnocache)][cachevd]
[wt|*wb] [nora|*ra] [*direct|cached] [CachedBadBBU|*NoCachedBadBBU] [Strip=<8|16|32|64|128|256|1024>]
[AfterVd=X] [Spares = [e:]s|[e:]s-x|[e:]s-x,y] [force]
Table 14 Add RAID Configuration Input Options
Option Value Range Description
type RAID [0|1|5|6|10|50|60]. Sets the RAID type of the configuration.
size Maximum size based on the physical drives Sets the size of each virtual drive. The default value
and RAID level. is for the capacity of all referenced disks.
name 15 characters of length. Specifies the drive name for each virtual drive.
drives Valid enclosure number and valid slot numbers In e:s|e:s-x|e:s-x,y:
for the enclosure. e specifies the enclosure ID.
s represents the slot in the enclosure.
e:s-x is the range convention used to
represent slots s to x in the enclosure e.
pdperarray 0 to 15. Specifies the number of physical drives per array.
The default value is automatically chosen.
sed — Creates security-enabled drives.
pdcache on|off|default. Enables or disables PD cache.
pi — Enables protection information.
dimmerswitch default: Logical device uses controller Specifies the power-saving policy.
default power-saving policy. Sets to default automatically.
automatic (auto): Logical device power
savings are managed by firmware.
none: No power-saving policy.
maximum (max): Logical device uses maximum
power savings.
MaximumWithoutCaching
(maxnocache): Logical device does not cache
write to maximize power savings.
direct|cached cached: Cached I/O. Sets the logical drive cache policy.
direct: Direct I/O. Direct I/O is the default.
LSI Corporation
- 31 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Virtual Drives Commands
Table 14 Add RAID Configuration Input Options (Continued)
Option Value Range Description
wt|wb wt: Write through. Enables write through.
wb: Write back. Write back is the default.
nora|ra ra: Read ahead. Disables read ahead.
nora: No read ahead. Enabled is the default.
cachedbadbbu|nocachedbadbbu cachedbadbbu: Enable bad BBU caching. Enables caching when BBU is not functioning.
nocachedbadbbu: Disable bad BBU caching. Disabled is the default.
cachevd — Enables SSD caching on the created virtual drive.
strip 8, 16, 32, 64, 128, 256, 512, 1024. Sets the strip size for the RAID configuration.
aftervd Valid virtual drive number. Creates the VD in the adjacent free slot next to the
specified VD.
spares Number of spare physical drives present. Specifies the physical drives that are to be assigned
to a disk group for spares.
force — Forces a security-capable physical drive to be added
to a drive group without security.
Input example:
storcli /c0 add vd type=raid10 size=2gb,3gb,4gb names=tmp1,tmp2,tmp3
drives=252:2-3,5,7 pdperarray=2
storcli /cx add vd cc|cachecade type=[0,1,10] drives=[e:]s|[e:]s-x|[e:]s-x,y [[wt|*wb] ]
[assignvds=0,1,2]
This command creates CacheCade virtual drives and associates existing virtual drives to CacheCade virtual drives. You
can use the following options to create the CacheCade virtual drive.
Table 15 Add RAID Configuration Input Options
Option Value Range Description
cachecade — Creates a CacheCade virtual drive.
type 0, 1, 10 Sets the RAID type of the CacheCade virtual drive.
drives Valid enclosure number and valid slot number See the drives row in the previous table for format.
wt|*wb wt: Enables write through. Enables or disables write cache.
wb: Enables write back.
assignvds Valid virtual drive number (0 to 63) Specifies the list of virtual drives associated with the new CacheCade
virtual drives.
Input example:
storcli /c0 add vd type=raid10 size=2gb,3gb,4gb names=tmp1,tmp2,tmp3
drives=252:2-3, 7
4.4.2 Delete Virtual Drives Commands
The Storage Command Line Tool supports the following virtual drive delete commands:
storcli /cx/vx|vall del
storcli /cx/vx|vall del cachecade
storcli /cx/vx|vall del force
LSI Corporation
- 32 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Virtual Drives Commands
NOTE If the virtual drive has user data, you must use the force option to delete the virtual drive.
A virtual drive with a valid master boot record (MBR) and a partition table is considered to contain user data.
If you delete a virtual drive with a valid MBR without erasing the data and then create a new virtual drive using the
same set of physical drives and the same RAID level as the deleted virtual drive, the old unerased MBR still exists at
block0 of the new virtual drive, which makes it a virtual drive with valid user data. Therefore, you must provide the
force option to delete this newly created virtual drive.
The detailed description for each command follows.
storcli /cx/vx|vall del
This command deletes a particular virtual drive or, when the vall option is used, all the virtual drives on the
controller are deleted.
Input example:
storcli /c0/v2 del
NOTE This command deletes virtual drives. Data located on these drives will no longer be accessible.
storcli /cx/vx|vall del cachecade
This command deletes a specific CacheCade virtual drive on a controller, or all the CacheCade configuration for
a controller.
Input example:
storcli /c0/vall del cachecade
NOTE This command deletes virtual drives. Data located on these drives will no longer be accessible.
storcli /cx/vx|vall del force
This command deletes a virtual drive only after the cache flush is completed. With the force option, the command
deletes a virtual drive without waiting for the cache flush to complete.
Input example:
storcli /c0/v2 del force
NOTE This command deletes the virtual drive where the operating system is present. Data located on these
drives and the operating system of the drive will no longer be accessible
4.4.3 Virtual Drive Show Commands
The Storage Command Line Tool supports the following virtual drive show commands:
storcli /cx/vx show
storcli /cx/vx show all
The detailed description for each command follows.
LSI Corporation
- 33 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Virtual Drives Commands
storcli /cx/vx show
This command shows the summary of the virtual drive information.
Input example:
storcli /c0/v0 show
storcli /cx/vx show all
This command shows all virtual drive information, which includes virtual drive information, physical drives used for
the virtual drives, and virtual drive properties.
Input example:
storcli /c0/v0 show all
4.4.4 Preserved Cache Commands
If a virtual drive becomes offline or is deleted because of missing physical disks, the controller preserves the dirty
cache from the virtual disk. The Storage Command Line Tool supports the following commands for preserved cache:
storcli /cx/vx delete preservedCache [force]
storcli /cx show preservedCache
The detailed description for each command follows.
storcli /cx/vx delete preservedcache
This command deletes the preserved cache for a particular virtual drive on the controller in missing state. Use the
force option to delete the preserved cache of a virtual drive in offline state.
Input example:
storcli /c0/v1 delete preservedcache
storcli /cx show preservedCache
This command shows the virtual drive that has preserved cache and whether the virtual drive is offline or missing.
Input example:
storcli /c0 show preservedCache
4.4.5 Change Virtual Drive Properties Commands
The Storage Command Line Tool supports the following commands to change virtual drive properties:
storcli /cx/vx set accesspolicy=<rw|ro|blocked|rmvblkd>
storcli /cx/vx set cachedbadbbu=<on|off>
storcli /cx/vx set iopolicy=<cached|direct>
storcli /cx/vx set name=<namestring>
storcli /cx/vx set pdcache=<on|off|default>
storcli /cx/vx set rdcache=<ra|nora>
storcli /cx/vx set security
storcli /cx/vx|vall set ssdcaching=<on|off>
storcli /cx/vx set wrcache=<wt|wb|awb>
The detailed description for each command follows.
LSI Corporation
- 34 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Virtual Drives Commands
storcli /cx/vx set accesspolicy=<rw|ro|blocked|rmvblkd>
This command sets the access policy on a virtual drive to read write, read only, or blocked or rmvblkd
(remove blocked).
Input example:
storcli /c0/v0 set accesspolicy=rw
storcli /cx/vx set cachedbadbbu=<on|off>
This command enables the use write cache for the virtual drive when the BBU is bad.
Input example:
storcli /c0/v0 set cachedbadbbu=on
storcli /cx/vx set iopolicy=<cached|direct>
This command sets the I/O policy on a virtual drive to cached I/O or direct I/O.
Input example:
storcli /c0/v0 set iopolicy=cached
storcli /cx/vx set name=<namestring>
This command names a virtual drive. The name is restricted to 15 characters
Input example:
storcli /c1/v0 set name=testdrive123
storcli /cx/vx set pdcache=<on|off|default>
This command sets the current disk cache policy on a virtual drive to on, off, or default setting.
Input example:
storcli /c0/v0 set pdcache=on
storcli /cx/vx set rdcache=<ra|nora>
This command sets the read cache policy on a virtual drive to read ahead, no read ahead, or adaptive read ahead.
Input example:
storcli /c0/v0 set rdcache=nora
storcli /cx/vx set security
This command secures the virtual drive.
Input example:
storcli /c0/v0 set security
NOTE The off option is not supported in the current release. If you run the command, a message saying that
the command is not supported appears.
storcli /cx/vx|vall set ssdcaching=<on|off>
This command assigns CacheCade virtual drives. If ssdcaching=off, the CacheCade virtual drive is removed.
Input example:
storcli /c0/v0 set ssdcaching=on
LSI Corporation
- 35 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Virtual Drives Commands
storcli /cx/vx set wrcache=<wt|wb|awb>
This command sets the write cache policy on a virtual drive to write back, write through, or always write back.
Input example:
storcli /c0/v0 set wrcache=wt
4.4.6 Virtual Drive Initialization Commands
The Storage Command Line Tool supports the following commands to initialize virtual drives:
storcli /cx/vx show init
storcli /cx/vx start init [full][Force]
storcli /cx/vx stop init
NOTE If the virtual drive has user data, you must use the force option to initialize the virtual drive.
A virtual drive with a valid MBR and partition table is considered to contain user data.
The detailed description for each command follows.
storcli /cx/vx show init
This command shows the initialization progress of a virtual drive in percentage.
Input example:
storcli /c0/v2 show init
storcli /cx/vx start init [full]
This command starts the initialization of a virtual drive. The default initialization type is fast initialization. If the full
option is specified, full initialization of the virtual drive starts.
Input example:
storcli /cx/vx start init [full]
storcli /cx/vx stop init
This command stops the initialization of a virtual drive. A stopped initialization cannot be resumed.
Input example:
storcli /c0/v0 stop init
4.4.7 Virtual Drive Erase Commands
The Storage Command Line Tool supports the following command to erase virtual drives:
storcli /cx/vx erase [force]
This command erases the data on the virtual drive. You can use the force option as a confirmation to erase the data
on the drive and the security information.
Input example:
storcli /c0/v0 erase[force]
NOTE If the virtual drive has user data, you must use the force option to erase the virtual drive.
A virtual drive with a valid MBR and partition table is considered to contain user data.
LSI Corporation
- 36 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Virtual Drives Commands
4.4.8 Virtual Drive Migration Commands
NOTE The virtual drive migration commands are not supported in Embedded MegaRAID.
The Storage Command Line Tool supports the following commands for virtual drive migration (reconstruction):
storcli /cx/vx show migrate
storcli /cx/vx start migrate <type=raidlevel>
[option=<add|remove> disk=<e1/s1,e2/s2 ...> ]
The detailed description for each command follows.
storcli /cx/vx show migrate
This command shows the progress of the virtual drive migrate operation in percentage.
Input example:
storcli /c0/v0 show migrate
storcli /cx/vx start migrate <type=raidlevel> [option=<add | remove> disk=<e1:s1,e2:s2 ...> ]
This command starts the reconstruction on a virtual drive to the specified RAID level by adding or removing disks
from the existing virtual drive. You can use the following options with the start migrate command:
Table 16 Virtual Drive Migration Command Options
Options Value Range Description
type = RAID level RAID [0|1|5|6] The RAID level to which the virtual drive must be
migrated.
[option=<add | remove> add: Adds disks to the virtual drive and starts Adds or removes disks from the virtual drive.
disk=<e1:s1,e2:s2, …>] reconstruction.
remove: Removes disks from the virtual drive and starts
reconstruction.
disk: The enclosure number and the slot number of the
disks to be added to the virtual drive.
Virtual drive migration can be done between the following RAID levels.
Table 17 Virtual Drive Migration Table
Initial RAID level Migrated RAID level
RAID 0 RAID 1
RAID 0 RAID 5
RAID 0 RAID 6
RAID 1 RAID 0
RAID 1 RAID 5
RAID 1 RAID 6
RAID 5 RAID 0
RAID 5 RAID 6
RAID 6 RAID 0
RAID 6 RAID 5
LSI Corporation
- 37 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Virtual Drives Commands
Input example:
storcli /c0/v3 start migrate type=r5 option=add disk=e5:s2,e5:s3
4.4.9 Virtual Drive Consistency Check Commands
The Storage Command Line Tool supports the following commands for virtual drive consistency checks:
storcli /cx/vx pause cc
storcli /cx/vx resume cc
storcli /cx/vx show cc
storcli /cx/vx start cc [force]
storcli /cx/vx stop cc
NOTE If enclosures are used to connect the physical drives to the controller, specify the IDs in the command.
The detailed description for each command follows.
storcli /cx/vx pause cc
This command pauses an ongoing consistency check process. You can resume the consistency check at a later time.
You can run this command only on a virtual drive that has a consistency check operation running.
Input example:
storcli /c0/v4 pause cc
storcli /cx/vx resume cc
This command resumes a suspended consistency check operation. You can run this command on a virtual drive that
has a paused consistency check operation.
Input example:
storcli /c0/v4 resume cc
storcli /cx/vx show cc
This command shows the progress of the consistency check operation in percentage.
Input example:
storcli /c0/v5 show cc
storcli /cx/vx start cc force
This command starts a consistency check operation for a virtual drive. Typically, a consistency check operation is run
on an initialized virtual drive. Use the force option to run a consistency check on an uninitialized drive.
Input example:
storcli /c0/v4 start cc
storcli /cx/vx stop cc
This command stops a consistency check operation. You can run this command only for a virtual drive that has a
consistency check operation running.
Input example:
storcli /c0/v4 stop cc
LSI Corporation
- 38 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Virtual Drives Commands
NOTE You cannot resume a stopped consistency check process.
4.4.10 Background Initialization Commands
The Storage Command Line Tool supports the following commands for background initialization:
storcli /cx/vx resume bgi
storcli /cx/vx set autobgi=<on|off>
storcli /cx/vx show autobgi
storcli /cx/vx show bgi
storcli /cx/vx stop bgi
storcli /cx/vx suspend bgi
The detailed description for each command follows.
storcli /cx/vx resume bgi
This command resumes a suspended background initialization operation.
Input example:
storcli /c0/v0 resume bgi
storcli /cx/vx set autobgi=<on|off>
This command sets the auto background initialization setting for a virtual drive to on or off.
Input example:
storcli /c0/v0 set autobgi=on
storcli /cx/vx show autobgi
This command shows the background initialization setting for a virtual drive.
Input example:
storcli /c0/v0 show autobgi
storcli /cx/vx show bgi
This command shows the background initialization progress on the specified virtual drive in percentage.
Input example:
storcli /c0/v0 show bgi
storcli /cx/vx stop bgi
This command stops a background initialization operation. You can run this command only for a virtual drive that is
currently initialized.
Input example:
storcli /c0/v4 stop bgi
LSI Corporation
- 39 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Foreign Configurations Commands
storcli /cx/vx pause bgi
This command suspends a background initialization operation. You can run this command only for a virtual drive that
is currently initialized.
Input example:
storcli /c0/v4 pause bgi
4.4.11 Virtual Drive Expansion Commands
The Storage Command Line Tool supports the following commands for virtual drive expansion:
storcli /cx/vx expand size=<value> [expandarray]
storcli /cx/vx|vall show expansion
The detailed description for each command follows.
storcli /cx/vx expand size=<value> [expandarray]
This command expands the virtual drive within the existing array or if you replace the drives with drives larger than
the size of the existing array. The value of the expand size is in GB. If the expandarray option is specified, the
existing array is expanded. If this option is not specified, the virtual drive is expanded.
storcli /cx/vx show expansion
This command shows the expansion information on the virtual drive with and without array expansion.
Input example:
storcli /c0/v0 show expansion
4.5 Foreign Configurations Commands
The Storage Command Line Tool supports the following commands to view, import, and delete
foreign configurations:
storcli /cx/fx|fall del|delete [ securitykey=sssss ]
storcli /cx/fx|fall import [preview][ securitykey=sssss ]
storcli /cx/fx|fall show [all] [ securitykey=sssss ]
NOTE Provide the security key when importing a locked foreign configuration created in a different machine
that is encrypted with a security key.
The detailed description for each command follows.
storcli /cx/fx|fall del| delete [ securitykey=sssss ]
This command deletes the foreign configuration of a controller. Input the security key if the controller is secured.
Input example:
storcli /c0/fall delete
LSI Corporation
- 40 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 BIOS-Related Commands
storcli /cx/fx|fall import [preview] [ securitykey=sssss ]
This command imports the foreign configurations of a controller. The preview option shows a summary of the
foreign configuration before importing it.
Input example:
storcli /c0/fall import
storcli /cx/fx|fall show [all][ securitykey=sssss ]
This command shows the summary of the entire foreign configuration for a particular controller. The all option
shows all the information of the entire foreign configuration.
NOTE The EID:Slot column is populated for the foreign PDs that are locked.
Input example:
storcli /c0/fall show preview foreign
storcli /c0/fall import preview
storcli /c0/fall show all
4.6 BIOS-Related Commands
The Storage Command Line Tool supports the following BIOS commands:
storcli /cx autobootselect(abs)=<on|off>
storcli /cx set bios=<on|off>
storcli /cx set headlessafemode|hsm=<on/off>
storcli /cx set headlesscontinueonerror|hcoe=<on/off>
storcli /cx set stoponerror|soe=<on|off>
storcli /cx show bios
The detailed description for each command follows.
storcli /cx set autobootselect|abs=<on|off>
This command enables the BIOS to select the best logical drive as the boot drive.
Input example:
storcli /cx set autobootselect=on
storcli /cx set bios=<on|off>
This commands enables or disables the MegaRAID controller's BIOS.
NOTE The legacy BIOS can load a limited number of the PCI device's BIOS. Disable the MegaRAID BIOS to
avoid issues during POST.
Input example:
storcli /c0 set bios=enable
LSI Corporation
- 41 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 BIOS-Related Commands
storcli /cx set headlessafemode|hsm=<on|off>
This command drives the MegaRAID BIOS to headless safe mode if any errors are encountered during POST. In
headless safe mode, limited support exists for the StorCLI commands.
Input example:
storcli /c0/ set headlessafemode=on
storcli /cx set headlesscontinueonerror|hcoe=<on|off>
This command does not drive the MegaRAID BIOS to headless safe mode if any errors are encountered during POST,
and it continues normal operation.
Input example:
storcli /c0/ set headlesscontinueonerror=on
storcli /cx set stoponerror|soe=<on|off>
This command stops the MegaRAID BIOS during POST if any errors are encountered.
Input example:
storcli /c0/ set StopOnError=on
storcli /cx show bios
This command shows if the BIOS is on or off.
Input example:
storcli /c0 show bios
4.6.1 OPROM BIOS Commands
The Storage Command Line Tool supports the following OPROM BIOS commands:
storcli /cx/ex/sx set bootdrive=on|off
storcli /cx/vx set bootdrive=on|off
storcli /cx show bootdrive
The detailed description for each command follows.
storcli /cx/ex/sx set bootdrive=on|off
This command sets the specified physical drive as the boot drive. During the next reboot, the BIOS looks for a boot
sector in the specified physical drive.
Input example:
storcli /c0/e32/s4 set bootdrive=on
storcli /cx/vx set bootdrive=on|off
This command sets the specified virtual drive as the boot drive. During the next reboot, the BIOS looks for a boot
sector in the specified virtual drive.
Input example:
storcli /c0/v0 set bootdrive=on
LSI Corporation
- 42 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Drive Group Commands
storcli/cx/vx show bootdrive
This command shows the boot drive for the controller. The boot drive can be a physical drive or a virtual drive.
Input example:
storcli /c0/v0 show bootdrive
4.7 Drive Group Commands
This section describes the drive group commands.
4.7.1 Drive Group Show
The Storage Command Line Tool supports the following drive group commands:
storcli /cx/dall show
storcli /cx/dall show all
storcli /cx/dall show cachecade
storcli /cx/dall show
This command shows the topology information of the drive group.
Input example:
storcli /c0/dall show
storcli /cx/dall show all
This command shows all available configurations in the controller which includes topology information, virtual drive
information, physical drive information, free space, and free slot information.
Input example:
storcli /c0/dall show all
storcli /cx/dall show cachecade
This command shows all CacheCade virtual drive information.
Input example:
storcli /c0/dall show cachecade
4.8 Dimmer Switch Commands
4.8.1 Change Virtual Drive Power Settings Commands
The Storage Command Line Tool supports the following command to change the Dimmer Switch® setting. The
Dimmer Switch is the power-saving policy for the virtual drive.
LSI Corporation
- 43 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Dimmer Switch Commands
storcli /cx/vx set ds=<default | auto | none | max | maxnocache>
This command changes the power-saving properties on a virtual drive. See dimmerswitch in the following table
for values.
Input example:
storcli /cx/vx set ds=default
NOTE Only the ds3 dimmer switch option cannot be selected in the Storage Command Line Tool.
You can use the following combinations for the dimmer switch commands:
storcli /cx set ds=off type=1|2|3|4
storcli /cx set ds=on type=1|2 [properties]
storcli /cx set ds=on type=3|4 defaultldtype=<value> [properties]
storcli /cx set ds=on [properties]
The following table describes the power-saving options.
Table 18 Dimmer Switch Input Options
Option Value Range Description
dimmerswitch or ds on|off Turns the dimmer switch option on.
type 1: Unconfigured Specifies the type of drives that the dimmer switch
2: Hot spare feature is applicable. By default, it is activated for
unconfigured drives, hot spare drives and virtual drives.
3: Virtual drive
4: All
defaultldtype auto: Logical device power savings are managed Specifies the default logical drive type that is created by
by the firmware. the dimmer switch option; set to none automatically.
none: No power saving policy.
max: Logical device uses maximum power savings.
maxnocache: Logical device does not cache write
to maximise power savings.
properties disableldps: Interval in hours or time in hh:mm Sets the interval or time in which the power-saving
format policy for the logical drive is turned off.
spinupdrivecount: Valid enclosure number (0 Specifies the number of drives in the enclosure that are
to 255) spun up.
SpinUpEncDelay: Valid time in seconds Specifies the delay of spin-up groups within an enclosure
in seconds.
storcli/cx show DimmerSwitch(ds)
This command shows the current dimmer switch setting for the controller.
Input example:
storcli/c0 show ds
LSI Corporation
- 44 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 BBU Commands
4.9 BBU Commands
The Storage Command Line Tool supports the following battery backup unit (BBU) commands:
storcli /cx/bbu show
storcli /cx/bbu show all
storcli /cx/bbu set bbuMode=<value>
storcli /cx/bbu set learndelayinterval=<value>
storcli /cx/bbu set powermode=sleep
storcli /cx/bbu set writeaceess=sealed
storcli /cx/bbu show modes
storcli /cx/bbu show properties
storcli /cx/bbu show status
storcli /cx/bbu start learn
The detailed description for each command follows.
storcli /cx/bbu show
This command shows the summary information for the BBU of a controller.
Input example:
storcli /c0/bbu show
storcli /cx/bbu show all
This command shows all the information of the BBU.
Input example:
storcli /c0/bbu show all
storcli /cx/bbu set bbuMode=<value>
This command sets the BBU mode for the BBU. The following table shows the various BBU modes:
Table 19 BBU Mode
Mode Description
0 48 hours of retentiona at 60 °C, 1-year Service Life.
1 12 hours of retention at 45 °C, 5-year Service Life, transparent learn.b
2 12 hours of retention at 55 °C, 3-year Service Life, transparent learn.
3 24 hours of retention at 45 °C, 3-year Service Life, transparent learn.
4 48 hours of retention at 45 °C, 3-year Service Life.
5 48 hours of retention at 55 °C, 1-year Service Life.
6 Same as the description for BBU mode 5. The BBU mode 6 enables you to receive events when the battery
capacity reaches suboptimal and critical thresholds.
a. Indicates how long the battery can hold data in the controller's memory in case of accidental system shutdown.
b. The controller's performance is not affected during the battery's learn cycle.
Input example:
storcli /c0/bbu set bbuMode=2
NOTE BBU modes are supported on any iBBU08/09 bbu/controller combo and later-generation controllers.
LSI Corporation
- 45 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 BBU Commands
storcli /cx/bbu set learndelayinterval=<value>
This command sets the learn delay interval for the BBU in hours. The value must be between 0 to 168 hours (7 days).
Input example:
storcli /c0/bbu set learnDelayInterval=30
storcli /cx/bbu set powermode=sleep
This command places the battery in low-power storage mode. The battery automatically exits this state after
5 seconds.
Input example:
storcli /c0/bbu set powermode=sleep
storcli /cx/bbu set writeaccess=sealed
This command seals the gas gauge EEPROM write access.
NOTE Use the set writeaccess=sealed command at manufacturing time.
Input example:
storcli /c0/bbu set writeaccess=sealed
storcli /cx/bbu show modes
This command shows the bbu mode information that includes the bbu mode number, retention time, service life,
maximum temperature, and battery learn information.
Input example:
storcli /c0/bbu show modes
storcli /cx/bbu show properties
This command shows the BBU Learn properties for a controller.
Input example:
storcli /c0/bbu show properties
storcli /cx/bbu show status
This command shows the battery information, firmware status, and the gas gauge status.
Input example:
storcli /c0/bbu show status
storcli /cx/bbu start learn
This command starts the BBU learning cycle. The battery learn cycle is immediately started and no other parameters
are required for this command.
Input example:
storcli /c0/bbu start learn
LSI Corporation
- 46 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Enclosure Commands
4.10 Enclosure Commands
The Storage Command Line Tool supports the following enclosure commands:
storcli /cx/ex download src=filepath[forceActivate]
storcli /cx/ex show all
storcli /cx/ex show status
The detailed description for each command follows.
storcli /cx/ex download src=filepath [forceactivate]
This command flashes the firmware with the file specified at the command line. The enclosure performs an error
check after the operation. The following option can be used with the enclosure firmware download command.
Table 20 Enclosure Firmware Download Command Options
Option Value Range Description
forceactivate — Issues a command descriptor block (CDB) with write command with no data with command
mode 0x0F (flash download already in progress).
NOTE This option is used primarily to activate Scotch Valley Enclosures.
NOTE The firmware file that is used to flash the enclosure can be of any format. The StorCLI utility assumes
that you provide a valid firmware image.
Input example:
storcli /c0/e0 download src=c:\file2.bin
storcli /cx/ex show all
This command shows all enclosure information, which includes general enclosure information, enclosure inquiry data,
a count of enclosure elements, and information about the enclosure elements.
Input example:
storcli /c0/e0 show all
storcli /cx/ex show status
This command shows the enclosure status and the status of all the enclosure elements.
Input example:
storcli /c0/e0 show status
4.11 PHY Commands
The Storage Command Line Tool supports the following PHY commands:
storcli /cx/px|pall set linkspeed=0(auto)|1.5|3|6|12
storcli /cx/px|pall show
storcli /cx/px|pall show all
The detailed description for each command follows.
LSI Corporation
- 47 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Logging Commands
storcli /cx/px|pall set linkspeed=0(auto)|1.5|3|6|12
This command sets the PHY link speed. You can set the speed to 1.5 Gb/s, 3 Gb/s, 6 Gb/s, or 12 Gb/s. The linkspeed is
set to auto when you specify linkspeed = 0.
Input example:
storcli /c0/p0 set linkspeed=1.5
storcli /cx/px|pall show
This command shows the basic PHY layer information.
Input example:
storcli /c1/p0 show
storcli /cx/px|pall show all
This command shows all the PHY layer information.
Input example:
storcli /c1/p0 show all
4.12 Logging Commands
The Storage Command Line Tool supports the following commands to generate and maintain log files:
storcli /cx clear events
storcli /cx delete termlog
storcli /cx show events file=<absolute path>
storcli /cx show eventloginfo
storcli /cx show termlog type=config|contents
The detailed description for each command follows.
storcli /cx delete events
This command deletes all records in the event log.
Input example:
storcli /c0 delete events
storcli /cx delete termlog
This command clears the TTY (firmware log for issue troubleshooting) logs.
Input example:
storcli /c0 delete termlog
storcli /cx show events file=<absolute path>
This command prints the system log to a text file and saves the file in the specified location.
Input example:
storcli /c0 show events file=C:\Users\brohan\test\eventreports
LSI Corporation
- 48 -
StorCLI Reference Manual Chapter 4: Working with the Storage Command Line Tool
January 2013 Logging Commands
storcli /cx show eventloginfo
This command shows the history of log files generated.
Input example:
storcli /c0 show eventloginfo type=config
storcli /cx show termlog type=config|contents
This command shows the firmware logs. The config option shows the term log configuration (settings of TTY BBU
buffering), the contents option shows the term log.The contents option is the default.
Input example:
storcli /c0 show termlog type=contents
LSI Corporation
- 49 -
StorCLI Reference Manual Chapter 5: Frequently Used Tasks
January 2013 Showing the Version of the Storage Command Line Tool
Chapter 5: Frequently Used Tasks
5.1 Showing the Version of the Storage Command Line Tool
The following command shows the version of the command line tool:
Storcli –v
5.2 Showing StorCLI Help
The following command shows the command line tool help:
Storcli –h
Help appears for all the StorCLI commands
5.3 Showing System Summary Information
The following command shows the summary of all the controller information:
Storcli –show [all]
5.4 Showing Free Space in a Controller
The following command shows the free space available in the controller:
Storcli /cx show freespace
5.5 Adding Virtual Drives
The following command creates a virtual drive:
Storcli /cx add vd type=raid[0|1|5|6|10|50|60][Size=<VD1_Sz>,<VD2_Sz>,..|*all]
[name=<VDNAME1>,..] drives=e:s|e:s-x|e:s-x,y [PDperArray=x|auto*]
[SED] [pdcache=on|off|*default][pi] [DimmerSwitch(ds)=default|automatic(auto)|
*none|maximum(max)|MaximumWithoutCaching(maxnocache)] [wt|*wb] [nora|*ra]
[*direct|cached] [CachedBadBBU|*NoCachedBadBBU]
[strip=<8|16|32|64|128|256|512|1024] [AfterVd=x] [Spares=[e:]s|[e:]s-x|[e:]s-x,y]
[force]
The following inputs can be used when adding virtual drives:
The controller in which the virtual drives are created.
The RAID type of the virtual drives. The supported RAID types are 0, 1, 5, 6, 10, 50, 60.
The size of each virtual drive.
LSI Corporation
- 50 -
StorCLI Reference Manual Chapter 5: Frequently Used Tasks
January 2013 Setting the Cache Policy in a Virtual Drive
The drives that are used to create the virtual drives.
drives = e:s|e:s-x|e:s-x,y
Where:
— e specifies the enclosure id.
— s represents the slot in the enclosure.
— e:s-x is the range conventions used to represents slots s to x in the enclosure e.
The physical drives per array. The physical drives per array can be set to a particular value.
The SED option creates security-enabled drives.
The PDcache option can be set to on or off.
The pi option enables protection information.
The dimmer switch is the power save policy. It can be set to default or automatic *, none, maximum(max),
or MaximumWithoutCaching(maxnocache).
The wt option disables write back.
The nora option disables read ahead.
The cached option enables the cached memory.
The CachedBadBBU option enables caching when bbu is not functional.
The strip option sets the strip size. It can take the values 8, 16, 32, 64, 128, 256, 512, 1024.
The AfterVdX option creates the virtual drives in the adjacent free slot next to the specified virtual drives.
NOTE The * indicates default values used in the creation of the virtual drives. If values are not specified, the
default values are taken.
Example: /cx add vd type=r1 drives=0:10-15 WB Direct strip=64
This command creates a RAID volume of RAID 1 type from drives in slots 10 to slot 15 in enclosure 0. The strip size
is 64kb.
5.6 Setting the Cache Policy in a Virtual Drive
The following command sets the write cache policy of the virtual drive:
Storcli /cx/v(x|all) set wrcache=wt|wb|awb
The command sets the write cache to write back, write through, or always write back.
5.7 Showing Virtual Drive Information
The following command shows the virtual drive information for all the virtual drives in the controller:
storcli /cx/vall show [all]
LSI Corporation
- 51 -
StorCLI Reference Manual Chapter 5: Frequently Used Tasks
January 2013 Deleting Virtual Drives
5.8 Deleting Virtual Drives
The following command deletes virtual drives:
storcli /cx/v(x|all) del [cc|cachecade]
The following inputs are required when deleting a virtual drive:
The controller on which the virtual drive or virtual drives is present.
The virtual drives that must be deleted; or you can delete all the virtual drives on the controller using the
vall option.
The cc or cachecade option to confirm that the deleted drive is a CacheCade drive.
5.9 Flashing Controller Firmware
The following command is used to flash the controller firmware.
storcli /cx download file=filepath [fwtype=<value>] [nosigchk]
[noverchk][resetnow]
For more information, see Section 4.2.6, Flashing Controller Firmware Command.
LSI Corporation
- 52 -
StorCLI Reference Manual Appendix A: 3Ware CLI Commands to StorCLI Command Conversion
January 2013
Appendix A: 3Ware CLI Commands to StorCLI Command Conversion
Table 1 System Commands
Description 3Ware CLI Command StorCLI Command
Show a general summary of all tw_cli show show
detected controllers. show ctrlcount
Table 2 Controller Commands
Description 3Ware CLI Command StorCLI Command
Show all information about the tw_cli /cx show all /cx show all
adapter, such as cluster state, BIOS,
alarm, firmware, version, and so on.
Download the firmware to all /cx update fw=filename_with_path /cx download src=filepath [nosigchk]
compatible controllers that can be [force] [noverchk]
flashed with the image. By default,
CLI checks for signature and version.
LSI Corporation
- 53 -
StorCLI Reference Manual Appendix A: 3Ware CLI Commands to StorCLI Command Conversion
January 2013
Table 2 Controller Commands (Continued)
Description 3Ware CLI Command StorCLI Command
Show the status of properties related /cx show <PropertyName> /cx show <PropertyName>
to the controllers.
The following properties can be used with this The following properties can be used with this
command: command:
a0,1,2|-aALL abortcconerror
achip activityforlocate
AENs [reverse] alarm
alarms [reverse] autorebuild
allunitstatus backplane
autocarve batterywarning
autorebuild bgirate
bios bootwithpinnedcache
carvesize cachebypass
ctlbus diag cacheflushint
dpmstat [type=<inst|ra|ext> ccrate
driver clusterenable
drivestatus coercion
events [reverse] copyback
exportjbod firmware directpdmapping
memory ds
model eccbucketleakrate
monitor eccbucketsize
numdrives enableeghsp
numports enableesmarter
numunits enableeug
ondegrade exposeencldevice
pcb jbod
pchip loadbalancemode
phy maintainpdfailhistory
rebuild migraterate
rebuildmode ncq
rebuildrate perfmode
selftest pr
serial prcorrectunconfiguredareas
spinup prrate
stagger rebuildrate
unitstatus rehostinfo
verify restorehotspare
verifymode safeid
verifyrate smartpollinterval
spinupdelay
spinupdrivecount
time
usefdeonlyencrypt
LSI Corporation
- 54 -
StorCLI Reference Manual Appendix A: 3Ware CLI Commands to StorCLI Command Conversion
January 2013
Table 2 Controller Commands (Continued)
Description 3Ware CLI Command StorCLI Command
Set properties on the selected autocarve=<on|off> abortcconerror=<on|off>
controllers. autodetect=<on|off > activityforlocate=<on|off>
disk=<p:-p>|all alarm=<on|off>
autorebuild=<on|off> autorebuild=<on|off>
carvesize=<1024..32768> backplane=<value>
dpmstat=<on|off> batterywarning=<on|off>
ondegrade=<cacheoff|follow> bgirate=<value>
rebuild=<enable|disable|><1..5> bootwithpinnedcache=<on|off>
rebuildmode=<adaptive|lowlatency> cachebypass=<on|off>
rebuildrate=<1..5> flush|flushcache
selftest=<enable|disable> cacheflushinterval=<value>
spinup=<value> ccrate=<value>
stagger=<value> coercion=<value>
verify=advanced|basic|<1..5> clusterenable=<value>
verify=basic [pref=ddd:hh]where copyback=<on|off>
hh={00..23} and type=<smartssd|smarthdd|all>
ddd={mon|tue|wed|thu|fri|sat|sun}
directpdmapping=<on|off>
verify=enable|disable|<1..5>
eccbucketleakrate=<value>
verifymode=<adaptive|lowlatency>
eccbucketsize=<value>
verifyrate=<1..5>
enableeghsp=<on|off>
enableesmarter=<value>
enableeug=<on|off>
exposeencldevice=<on|off>
foreignautoimport=<on|off>
jbod=<on|off>
loadbalancemode=<value>
maintainpdfailhistory=<on|off>
migraterate=<value>
ncq=<on|off>
perfmode=<value>
prcorrectunconfiguredareas=<on|off>
prrate=<value>
rebuildrate=<value>
restorehotspare=<on|off>
smartpollinterval=<value>
spinupdelay=<value>
spinupdrivecount=<value>
stoponerror=<on|off>
usefdeonlyencrypt=<on|off>
time=yyyymmdd hh:mm:ss|systemtime
usefdeonlyencrypt=<on|off>
LSI Corporation
- 55 -
StorCLI Reference Manual Appendix A: 3Ware CLI Commands to StorCLI Command Conversion
January 2013
Table 3 Alarm Commands
Description 3Ware CLI Command StorCLI Command
Set alarm properties. /cx/ex/almx set /cx set alarm=<on|off|silence>
alarm=<mute|unmute|off>
NOTE The StorCLI controllers have controller alarms.
NOTE The 3ware® controllers have enclosure alarms.
Show alarm properties. /cx/ex show alarms /cx show alarm
NOTE This command applies for only 9750 and
9690SA controllers.
Table 4 Patrol Read and Consistency Check Commands
Description 3Ware CLI Command StorCLI Command
Show patrol read status and patrol /cx/ux show /cx show patrolRead
read parameters, if any in progress.
Set the patrol read options on a /cx/ux start verify /cx set patrolread {=on
single adapter, multiple adapters, or /cx/ux set autoverify=<on|off> mode=<auto|manual>}|{off}
all adapters (x = single controller). /cx add verify=dddh:hh:duration /cx set patrolread [starttime=<
yyyy/mm/dd hh>]
[maxconcurrentpd=<value>]
[includessds=<on|off>]
[uncfgareas=on|off]
/cx set patrolread delay=<value>
Show consistency check status, if any /cx/ux show /cx/vx show cc
in progress, and consistency check /cx show ccrate
parameters.
Set consistency check options on a /cx/ux start verify storcli /cx set
single adapter, multiple adapters, or /cx/ux set autoverify=<on|off> consistencycheck|cc=[off|seq|conc]
all adapters (x = single controller). [delay=value]
/cx add verify=ddd:hh:duration
[starttime=yyyy/mm/dd hh]
[excludevd=x-y,z]
NOTE The 3Ware CLI combines both patrol read and consistency check into a single command. The StorCLI
has different commands for each.
LSI Corporation
- 56 -
StorCLI Reference Manual Appendix A: 3Ware CLI Commands to StorCLI Command Conversion
January 2013
Table 5 BBU Commands
Description 3Ware CLI Command StorCLI Command
Show complete BBU information, /cx/bbu show all /cx/bbu show all
such as status, capacity information,
design information, and properties.
Show BBU summary information. /cx/bbu show /cx/bbu show
Show BBU properties. /cx/bbu show batinst /cx/bbu show properties
/cx/bbu show bootloader /cx/bbu show status
/cx/bbu show fw
NOTE Not all the properties shown in the 3Ware CLI
/cx/bbu show lasttest
are shown in the StorCLI.
/cx/bbu show pcb
/cx/bbu show serial
/cx/bbu show status
/cx/bbu show temp
/cx/bbu show tempstat
/cx/bbu show tempval
/cx/bbu show volt
Show BBU capacity information. /cx/bbu show cap /cx/bbu show all
Start the learning cycle on the BBU. /cx/bbu test [quiet] /cx/bbu start learn
Table 6 Virtual Drive Commands
Description 3Ware CLI Command StorCLI Command
Create a RAID volume of the specified /cx add vd type=<RaidType> /cx add vd
RAID type. disk=<p:p|p-p|p:p-p> (where p=port or type=raid[0|1|5|6|10|50|60]
drive number) [[size=<vd1_size>,<vd2_size>,..|
[strip=<size>] [nocache|nowrcache] *all][name=<vdname1>,..]
[nordcache|rdcachebasic] drives=e:s|e:s-x|e:s-x,y;e:s-x,y,z
[pdperarray=x|*auto] [sed] [name=string (9000 series)]
[pdcache=on|off|*default ] [ignoreECC]
[pi][dimmerswitch| [autoverify|noautoverify]
ds=default|automatic(auto)|
v0=n|vol=a:b:c:d] (n, a, b, c, d=size of *none|maximum(max)
volume in GB)
|maximumwithoutcaching(maxnocache)]
[noqpolicy] [wt|*wb] [nora|*ra] [*direct|cached]
[storsave=<protect|balance|perform> [cachedbadbbu|*nocachedbadbbu]
] [strip=<8|16|32|64|128|256|512|
[noscan] 1024] [aftervd=x]
[rapidrecovery=<all|rebuild|disable [ spares=[e:]s|[e:]s-x|[e:]s-
>] x,y;[e:]s-x,y,z > ] [force]
[group=<3|4|5|6|7|8|9|10|11|12|13|
14|15|16>]
RaidType={raid0, raid1, raid5,
raid10, raid50, single, spare,
raid6}
Delete virtual drives. /cx/ux del [quiet] /cx/vx[all] delete [force]
[cachecade]
NOTE You can delete a single unit using this
command. NOTE You can delete one virtual disk, multiple
virtual disks, or all the selected virtual disks on
selected adapters using this command.
LSI Corporation
- 57 -
StorCLI Reference Manual Appendix A: 3Ware CLI Commands to StorCLI Command Conversion
January 2013
Table 6 Virtual Drive Commands (Continued)
Description 3Ware CLI Command StorCLI Command
Show drive group information. /cx/ux show [all] /cx/dall show [cachecade]
NOTE Information of each unit is shown individually.
Scan and show available foreign /cx rescan cx/fx[all] show [preview]
configurations, provide a preview of [ securityKey=sssss ]
the imported foreign configuration, cx/fx[all] import [ securityKey=sssss ]
show or import foreign
configuration.
Show VD information, including /cx/ux show [all] /cx/vx show all
name, RAID level, RAID level qualifier,
size in MBs, state, strip size, number
of drives, span depth, cache policy,
access policy, and any ongoing
activity progress, which includes
initialization, background
initialization, consistency check, and
reconstruction.
Show the virtual drive properties. /cx/ux show autoverify /cx/vx show all
/cx/ux show identify
NOTE The StorCLI does not have commands to
/cx/ux show ignoreECC show individual virtual drive properties.
/cx/ux show initializestatus
/cx/ux show name
/cx/ux show parit
/cx/ux show qpolicy
/cx/ux show rapidrecovery
/cx/ux show rdcache
/cx/ux show rebuildstatus
/cx/ux show serial
/cx/ux show status
/cx/ux show storsave
/cx/ux show verifystatus
/cx/ux show volumes
/cx/ux show wrcache
Set virtual drive properties. /cx/ux set autoverify=on|off /cx/vx set
/cx/ux set cache=on|off [quiet] accesspolicy=<rw|ro|blocked|
rmvblkd>
/cx/ux set identify=on|off
/cx/vx set cachedbadbbu=<on|off>
/cx/ux set ignoreECC=on|off
/cx/vx set iopolicy=<cached|direct>
/cx/ux set name=string
/cx/vx set name=<namestring>
/cx/ux set qpolicy=on|off
/cx/vx set pdcache=<on|off|default>
/cx/ux set
rapidrecovery=all|rebuild|disable /cx/vx set rdcache=<ra|nora|adra>
/cx/ux set /cx/vx set security=<on|off>
rdcache=basic|intelligent|off /cx/vx|vall set ssdcaching=<on|off>
/cx/ux set /cx/vx set wrcache=<wt|wb|fwb>
storsave=protect|balance|perform
[quiet]
/cx/ux set wrcache=on|off [quiet]
LSI Corporation
- 58 -
StorCLI Reference Manual Appendix A: 3Ware CLI Commands to StorCLI Command Conversion
January 2013
Table 6 Virtual Drive Commands (Continued)
Description 3Ware CLI Command StorCLI Command
Show cache and access policies of the /cx/ux show [all] /cx/vx show all
virtual drive. /cx/ux show autoverify
NOTE The StorCLI does not have commands to
/cx/ux show cache
show individual virtual drive properties.
/cx/ux show identify
/cx/ux show ignoreECC
/cx/ux show name
/cx/ux show parit
/cx/ux show qpolicy
/cx/ux show rapidrecovery
/cx/ux show rdcache
/cx/ux show rebuildstatus
/cx/ux show serial
/cx/ux show status initializestatus
/cx/ux show storsave
/cx/ux show verifystatus
/cx/ux show volumes
/cx/ux show wrcache
Start initialization (writing 0s) on the /cx/ux start verify /cx/vx start init [Full]
virtual drive.
NOTE Only the bios can do a foreground
initialization. A background initialization does
otherwise. A verify starts a back ground initialization.
Stop an ongoing initialization on the /cx/ux stop verify /cx/vx stop init
virtual drive.
NOTE Only the bios can do a foreground
initialization. A background initialization does
otherwise. A verify starts a back ground initialization
Show a snapshot of the ongoing /cx/ux show [all] /cx/vx show init
initialization, if any.
NOTE Only the bios can do a foreground
initialization. A background initialization does
otherwise. A verify starts a back ground initialization.
Start a consistency check on the /cx/ux start verify /cx/vx start cc
virtual drive.
Stop a consistency check on the /cx/ux stop verify /cx/vx stop cc
virtual drive.
Reconstruct the selected virtual disk /cx/ux migrate type=<RaidType> /cx/vx start migrate
to a new RAID level. [disk=<p:-p..>] [strip=<size>] <type=raidlevel> [option=<add |
[noscan] [nocache] [autoverify] remove> disk=<e1:s1,e2:s2 ..> ]
[group=<3|4|5|6|7|8|9|10|11|12|13|1 /cx/vx show migrate
4|15|16>]
RaidType={ raid0, raid1, raid5,
raid10, raid50, single, raid6 }
Change the power-saving setting on /cx/ux set powersavestandbytimer=<5 /cx/vx set ds=<default | Auto | None
the virtual drive. to 999> | Max | MaxNoCache>
LSI Corporation
- 59 -
StorCLI Reference Manual Appendix A: 3Ware CLI Commands to StorCLI Command Conversion
January 2013
Table 7 Physical Drive Commands
Description 3Ware CLI Command StorCLI Command
Show physical disk information. /cx/px show [all] /cx[/ex]/sx show [all]
Start, stop, suspend, or resume an /cx/ux start rebuild disk=<p:-p...> /cx[/ex]/sx start rebuild
ongoing rebuild operation. [ignoreECC] /cx[/ex]/sx stop rebuild
/cx[/ex]/sx pause rebuild NOTE Rebuilds cannot be stopped or paused.
/cx[/ex]/sx resume rebuild
Mark the configured physical disk /cx/px remove [quiet] /cx[/ex]/sx set missing
drive as missing for the selected
adapter.
Change the physical disk drive state /cx/px remove [quiet] /cx[/ex]/sx set offline
to offline.
Add jbod. /cx add vd type=jbod disk=<p> /cx[/ex]/sx set jbod
(where p = port or drive number)
Change the physical disk drive hot /cx add vd type=spare /cx[/ex]/sx add hotsparedrive
spare state and associate the drive to disk=<p:p|p-p|p:p-p> [{dgs=<N|0,1.2...n,,>]
an enclosure and virtual disk. (where p = port or drive number) [EnclAffinity][nonRevertible]
Locate the physical disk drive and /cx/px set identify=on|off /cx[/ex]/sx start | stop locate
activate the physical disk activity LED.
Prepare the unconfigured physical /cx/px remove [quiet] /cx[/ex]/sx spindown
drive for removal.
Show information about all physical /cx/px show [all] /cx/eall/sall show [all]
disk drives and other devices
connected to the selected adapters;
includes drive type, size, serial
number, and firmware version.
Download drive or expander /cx/px update fw=image.name [force] /cx[/ex]/sx download src=filepath
firmware. [satabridge]
Table 8 Enclosure Commands
Description 3Ware CLI Command StorCLI Command
Show information about the /cx/ex show [all] /cx/ex show [all]
enclosure for the selected adapter.
Show the status of the enclosure /cx/ex show [all] /cx/ex show status
connected to the selected adapter. /cx/ex show controllers
/cx/ex show slots
/cx/ex show fans
/cx/ex show temp
/cx/ex show pwrs
/cx/ex show alms
Download enclosure firmware. /cx/ex update fw=image.name [force] /cx/ex download src=filepath
[offline] [forceActivate
LSI Corporation
- 60 -
StorCLI Reference Manual Appendix A: 3Ware CLI Commands to StorCLI Command Conversion
January 2013
Table 9 Events and Logs
Description 3Ware CLI Command StorCLI Command
Show the total number of events, /cx show alarms /cx show eventloginfo
newest and oldest sequence number,
shutdown sequence number, reboot NOTE This command shows AENs since last
sequence number, clear sequence controller reset.
number.
Show the total event entries available /cx show alarms /cx show events filter=<Info |
at the firmware since last clear, and warning| critical| fatal >
details of each entries of error log. NOTE This command shows AENs since last file=<path of the file>
controller reset.
Show the count of events starting /cx show alarms /cx show events type=<sinceShutDown
from specified seqNum and | sinceReboot |ccincon vd=<0,1,2…>
matching category and severity NOTE This command shows AENs since last | includeDeleted | latest=x
controller reset. filter=<Info | warning| critical|
fatal > file=<path of the file>
Show TTY firmware terminal log /cx show diag /cx show TermLog
entries with details on given [type=contents|Config]
adapters. The information is shown as
total number of entries available on
the firmware side.
Table 10 Miscellaneous Commands
Description 3Ware CLI Command StorCLI Command
Show version information. tw_cli ? ver
Show help for all show commands at tw_cli ? show help
server level. tw_cli /cx ?
tw_cli /cx/ux ?
tw_cli /cx/px ?
tw_cli /cx/phyx ?
tw_cli /cx/bbu ?
tw_cli /cx/ex ?
tw_cli /ex
NOTE 3 Ware CLI shows context sensitive help.
Show PHY connection information /cx/phyx show /cx/px show
for physical PHY medium on the
adapters.
Set PHY link speed. /cx/phyx set /cx/px set
link=<0|1.5|3.0|6.0|12.0> linkspeed=0(auto)|1.5|3|6|12
LSI Corporation
- 61 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Appendix B: MegaCLI Commands to StorCLI Command Conversion
Table 11 System Commands
Description MegaCLI Command StorCLI Command
Show the software version. MegaCLI -v storcli -v
Show help information. MegaCLI -help|-h|? storcli -help|-h|?
Show the number of controllers connected. MegaCLI -adpCount storcli show ctrlcount
LSI Corporation
- 62 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Table 12 Controller Commands
Description MegaCLI Command StorCLI Command
Show the status of properties related MegaCli -AdpGetProp /cx show <propertyName>
to the controllers. <PropertyName>-aN|-a0,1,2|-aALL
The following properties can be used with this
The following properties can be used with this command:
command: activityforlocate
abortcconerror alarm
alarmdsply backplane
autodetectbackplanedsbl batterywarning
autoenhancedimportdsply bgirate
autosnapshotspace bootwithpinnedcache
batwarndsbl cachebypass
bgirate cacheflushint
bootwithpinnedcache cc
cachebypass ccrate
ccrate clusterenable
clusterenable coercion
coercionmode copyback
copybackdsbl directpdmapping
defaultldpspolicy ds
defaultsnapshotspace eccbucketleakrate
defaultviewspace eccbucketsize
disableldpsinterval enableeghsp
disableldpstime enableesmarter
disableocr enableeug
dsbl exposeencldevice
eccbucketcount jbod
eccbucketleakrate loadbalancemode
eccbucketsize maintainpdfailhistory
enableeghsp migraterate
enableesmarter ncq
enableeug| perfmode
enablejbod pr
enblspindownunconfigdrvs prcorrectunconfiguredareas
loadbalancemode prrate
maintainpdfailhistoryenbl rebuildrate
ncqdsply rehostinfo
patrolreadrate restorehotspare
perfmode safeid
predfailpollinterval smartpollinterval
rebuildrate spinupdelay
reconrate spinupdrivecount
rstrhotspareoninsert time
smartcpybkenbl usefdeonlyencrypt
spindowntime
spinupdelay
spinupdrivecount
spinupencdelay
LSI Corporation
- 63 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Table 12 Controller Commands (Continued)
Description MegaCLI Command StorCLI Command
Show the status of properties related spinupencdrvcnt
to the controllers (continued). ssdsmartcpybkenbl
usediskactivityforlocate
usefdeonlyencrypt
LSI Corporation
- 64 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Table 12 Controller Commands (Continued)
Description MegaCLI Command StorCLI Command
Set properties on the selected Megacli -AdpSetProp /cx set <property1>
controllers. <propertyname>-an|-a0,1,2|-aall
The following properties can be set using this The following properties can be set using this command:
command: abortcconerror=<on|off>
abortcconerror activityforlocate=<on|off>
alarmdsply alarm=<value>
autodetectbackplanedsbl autorebuild=<on|off>
autoenhancedimportdsply backplane=<value>
autosnapshotspace batterywarning=<on|off>
batwarndsbl bgirate=<value>
bgirate bootwithpinnedcache=<on|off>
bootwithpinnedcache cachebypass=<on|off>
cachebypass flush|flushcache
ccrate cacheflushinterval=<value>
clusterenable ccrate=<value>
coercionmode coercion=<value>
copybackdsbl clusterenable=<value>
defaultldpspolicy copyback=<on|off>
defaultsnapshotspace type=<smartssd|smarthdd|all>
defaultviewspace dimmerswitch=<on|off>
disableldpsinterval directpdmapping=<on|off>
disableldpstime eccbucketleakrate=<value>
disableocr eccbucketsize=<value>
dsbl enableeghsp=<value>
eccbucketcount enableesmarter=<value>
eccbucketleakrate enableeug=<value>
eccbucketsize exposeencldevice=<on|off>
enableeghsp foreignautoimport=<on|off>
enableesmarter jbod=<on|off>
enableeug| loadbalancemode=<value>
enablejbod maintainpdfailhistory=<on|off>
enblspindownunconfigdrvs migraterate=<value>
loadbalancemode ncq=<on|off>
maintainpdfailhistoryenbl perfmode=<value>
ncqdsply prcorrectunconfiguredareas=<on|off>
patrolreadrate prrate=<value>
perfmode rebuildrate=<value>
predfailpollinterval restorehotspare=<on|off>
rebuildrate smartpollinterval=<value>
reconrate spinupdelay=<value>
rstrhotspareoninsert spinupdrivecount=<value>
smartcpybkenbl stoponerror=<on|off>
spindowntime usefdeonlyencrypt=<on|off>
spinupdelay time=yyyymmdd hh:mm:ss|systemtime
spinupdrivecount usefdeonlyencrypt=<on|off>
spinupencdelay
LSI Corporation
- 65 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Table 12 Controller Commands (Continued)
Description MegaCLI Command StorCLI Command
Set properties on the selected spinupencdrvcnt
controllers (continued) sdsmartcpybkenbl
usediskactivityforlocate
usefdeonlyencrypt
Show the number of controllers MegaCLI -adpCount storcli show ctrlcount
connected.
Show all information about the MegaCli -AdpAllInfo storcli /cx show all
adapter, such as cluster state, BIOS, -aN|-a0,1,2|-aALL
alarm, firmware, version, and so on.
Show the freespace available in the MegaCLI -CfgFreeSpaceinfo storcli /cx show freespace
controller. -aN|-a0,1,2|-aALL
Download the controller firmware. MegaCli -AdpFwFlash -f filename storcli /cx download file=<filepath>
[-NoSigChk] [-NoVerChk] [fwtype=<val>] [nosigchk]
[-ResetNow] -aN|-a0,1,2|-aALL [noverchk][resetnow]
Show the preserved cache status. MegaCLI-GetPreservedCacheList storcli /cx show preservedcache
-aN|-a0,1,2|-aALL
Set the controller time MegaCLI –AdpSetTime yyyymmdd storcli /c(x|all) set time=<yyyymmdd
hh:mm:ss -aN|-a0,1,2|-aALL hh:mm:ss | systemtime>
Show the controller time. MegaCLI –AdpGetTime -aN storcli /cx show time
Table 13 Patrol Read Commands
Description MegaCLI Command StorCLI Command
Show the patrol read status and MegaCli -AdpPR -info storcli/cx show patrolRead
patrol read parameters, if any in -aN|-a0,1,2|-aALL
progress.
Set the patrol read options on a MegaCli -AdpPR storcli /cx set patrolread {=on
single adapter, multiple adapters, or –Dsbl|EnblAuto|EnblMan|Start|Stop| mode=<auto|manual>}|{off}
all adapters. Info|Suspend|Resume|Stop| storcli /cx set patrolread
SSDPatrolReadEnbl | [starttime=< yyyy/mm/dd hh>] (x = single controller).
SSDPatrolReadDsbl [maxconcurrentpd=<value>]
|{SetDelay Val}|{-SetStartTime [includessds=<on|off>]
yyyymmdd hh}|{maxConcurrentPD Val} [uncfgareas=on|off]
-aN|-a0,1,2|-aALL storcli /cx set patrolread
delay=<value>
Disable patrol read. MegaCli -AdpPR -Dsbl storcli /cx set patrolread=off
-aN|-a0,1,2|-aALL
Enable automatic patrol read. MegaCli -AdpPR -EnblAuto storcli /cx set patrolread=on
-aN|-a0,1,2|-aALL mode=auto
Enable manual patrol read. MegaCli -AdpPR -EnblMan storcli /cx set patrolread=on
-aN|-a0,1,2|-aALL mode=manual
Start patrol read. MegaCli -AdpPR -Start storcli /cx start patrolRead
-aN|-a0,1,2|-aALL
Suspend a running patrol read. MegaCli -AdpPR -Suspend storcli /cx suspend patrolread
-aN|-a0,1,2|-aALL
Resume a suspended patrol read. MegaCli -AdpPR -Resume storcli /cx resume patrolread
-aN|-a0,1,2|-aALL
LSI Corporation
- 66 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Table 13 Patrol Read Commands (Continued)
Description MegaCLI Command StorCLI Command
Stop a running patrol read. MegaCli -AdpPR -Stop storcli /cx stop patrolRead
-aN|-a0,1,2|-aALL
Include SSD drives in patrol read. MegaCli -AdpPR -SSDPatrolReadEnbl storcli /cx set patrolRead
-aN|-a0,1,2|-aALL includessds=on | onlymixed
Exclude SSD drives in patrol read. MegaCli -AdpPR -SSDPatrolReadDsbl storcli /cx set patrolRead
-aN|-a0,1,2|-aALL includessds=off
Delay a patrol read, MegaCli -AdpPR -SetDelay Val storcli /cx set patrolread
-aN|-a0,1,2|-aALL delay=<value>
Schedule a patrol read. MegaCli -AdpPR -SetStartTime storcli /cx set patrolread=on
yyyymmdd hh -aN|-a0,1,2|-aALL starttime=YYYY/MM/DD HH
Set the value for maximum MegaCli -AdpPR -maxConcurrentPD Val storcli /cx set patrolread
concurrent physical drives for the -aN|-a0,1,2|-aALL maxconcurrentpd=xx
patrol read.
Table 14 Consistency Check Commands
Description MegaCLI Command StorCLI Command
Schedule a consistency check. MegaCLI -AdpCcSched -Dsbl|-Info| storcli /cx set
{-ModeConc | -ModeSeq [-ExcludeLD consistencycheck|cc=[off|seq|conc]
-LN|-L0,1,2] [-SetStartTime yyyymmdd [delay=value] starttime=yyyy/mm/dd
hh ] [-SetDelay val ] } hh [excludevd=x-y,z]
-aN|-a0,1,2|-aALL
Show consistency check status and MegaCLI -AdpCcSched -Info storcli /cx show cc/ConsistencyCheck
consistency parameters, in progress,
if any.
Table 15 OPROM BIOS Commands
Description MegaCLI Command StorCLI Command
Schedule a consistency check. MegaCli -AdpBIOS -Dsply storcli /cx show bios
-aN|-a0,1,2|-aALL
Show consistency check status and MegaCli -AdpBootDrive -{-Set {-Lx | storcli /cx/ex/sx set
consistency parameters, if any in -physdrv[E0:S0]}} -aN|-a0,1,2|-aALL bootdrive=on|off
progress. storcli /cx/vx set bootdrive=on|off
Sets the BIOS properties for the MegaCli -AdpBIOS -Enbl | -Dsbl | storcli /cx set bios=<on|off>
controller. -Dsply | SOE | BE storcli /cx set
EnblAutoSelectBootLd | stoponerror|soe=<on|off>
DsblAutoSelectBootLd
storcli /cx set -aN|-a0,1,2|-aALL
autobootselect(abs)=<on|off>
LSI Corporation
- 67 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Table 16 Battery Commands
Description MegaCLI Command StorCLI Command
Show battery-related information. MegaCli -AdpBbuCmd -aN|-a0,1,2|-aALL storcli /cx/bbu show
storcli /cx/bbu show all
Show the battery learn properties. MegaCli -AdpBbuCmd -GetBbuProperties storcli /cx/bbu show properties
-aN|-a0,1,2|-aALL
Show the battery information, MegaCli -AdpBbuCmd -GetBbuStatus storcli /cx/bbu show status
firmware status, and the gas gauge -aN|-a0,1,2|-aALL
status.
Show battery capacity information. MegaCli -AdpBbuCmd storcli /cx/bbu show all
-GetBbuCapacityInfo
-aN|-a0,1,2|-aALL
Show battery design information. MegaCli -AdpBbuCmd -GetBbuDesignInfo storcli /cx/bbu show all
-aN|-a0,1,2|-aALL
Set battery properties MegaCli -AdpBbuCmd -SetBbuProperties storcli /cx/bbu set
-f <fileName> -aN|-a0,1,2|-aALL learnDelayInterval=<value>
storcli /cx/bbu set bbuMode=<value>
storcli /cx bbu set
autolearnmode=<value>,
where x= 0 – Enabled, 1 – Disabled, 2 – Warn though
event.
Start battery learn cycle. MegaCli -AdpBbuCmd -BbuLearn storcli /cx/bbu start learn
-aN|-a0,1,2|-aALL
Set the battery to low power storage MegaCli -AdpBbuCmd -BbuMfgSleep storcli /cx/bbu set powermode=sleep
mode. -aN|-a0,1,2|-aALL
Seal the gas gauge EEPROM write MegaCli -AdpBbuCmd -BbuMfgSeal storcli /cx/bbu set
access -aN|-a0,1,2|-aALL writeaccess=sealed
LSI Corporation
- 68 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Table 17 RAID Configuration Commands
Create a RAID configuration of RAID MegaCli –CfgLDAdd storcli /cx add vd
type 0, 1, 5, and 6. -R0|-R1|-R5|-R6[E0:S0,E1:S1,...] type=raid[0|1|5|6]
[WT | WB] [NORA | RA | ADRA] [Size=<VD1_Sz>,<VD2_Sz>,..|*all]
[Direct | Cached] [name=<VDNAME1>,..]
[CachedBadBBU|NoCachedBadBBU] drives=e:s|e:s-x|e:s-x,y;e:s-x,y,z
[-szXX [-szYY [... ]]] [PDperArray=x]
[-strpszM] [–Hsp[E5:S5,...]]
[SED] [pdcache=on|off|*default][pi] [–afterLdX] -aN
[DimmerSwitch(ds)=default|automatic
(auto)|*none|maximum(max)
|MaximumWithoutCaching(maxnocache)]
[wt|*wb] [nora|*ra] [*direct|cached]
[CachedBadBBU|*NoCachedBadBBU]
[strip=<8|16|32|64|128|256|512|1024
] [AfterVd=X]
[Spares=[e:]s|[e:]s-x|[e:]s-x,y]
[force]
Create a CacheCade virtual drive. MegaCLI -CfgCacheCadeAdd [-rX] storcli /cx add vd cachecade|cc
-Physdrv[E0:S0,...] {-Name Type=[0,1,10]
LdNamestring} [WT|WB|ForcedWB] drives=[e:]s|[e:]s-x|[e:]s-x,y
[-assign -LX|L0,2,5..|LALL] [ < WT| WB> ] [assignvds=0,1,2]
-aN|-a0,1,2|-Aall
Create a RAID configuration of RAID MegaCli –CfgSpanAdd storcli /cx add vd
type 10, 50, and 60. -aN|-a0,1,2|-aALL type=raid[10|50|60]
-R10|-R50|R60 [Size=<VD1_Sz>,<VD2_Sz>,..|*all]
–Array0[E0:S0,E1:S1,...] [name=<VDNAME1>,..]
–Array1[E0:S0,E1:S1,...] [...] drives=e:s|e:s-x|e:s-x,y;e:s-x,y,z
[WT | WB] [NORA | RA | ADRA] [PDperArray=x]
[Direct | Cached]
[SED] [pdcache=on|off|*default][pi] [CachedBadBBU|NoCachedBadBBU]
[DimmerSwitch(ds)=default|automatic [-szXX [-szYY [... ]]]
(auto)|*none|maximum(max) [-strpszM] [–afterLdX] -aN
|MaximumWithoutCaching(maxnocache)]
[wt|*wb] [nora|*ra] [*direct|cached]
[CachedBadBBU|*NoCachedBadBBU]
[strip=<8|16|32|64|128|256|512|1024
] [AfterVd=X]
[Spares=[e:]s|[e:]s-x|[e:]s-x,y]
[force]
Delete a virtual drive. MegaCli -CfgClr [-Force] storcli /cx/vall delete
-aN|-a0,1,2|-aALL
Show the topology information of MegaCLI -CfgDsply storcli /cx/dall show [all]
the drive group. -aN|-a0,1,2|-Aall
Show information for a CacheCade MegaCLI -CfgCacheCadeDsply storcli /cx/dall show CacheCade(cc)
virtual drive. -aN|-a0,1,2|-Aall
LSI Corporation
- 69 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Table 17 RAID Configuration Commands (Continued)
Delete a virtual drive hosting the MegaCLI -CfgLdDel storcli /cx/vx[all] delete -force
operating system. -LX|-L0,2,5...|-LALL [-Force]
-aN|-a0,1,2|-aALL
Delete a CacheCade virtual drive. MegaCLI -CfgCacheCadeDel storcli /cx/vx[all] delete
-LX|-L0,2,5...|-LALL CacheCade(cc)
-aN|-a0,1,2|-Aall
Show, delete, and import the foreign MegaCli –CfgForeign –Scan | storcli /cx/f(x|all) show [all]
configuration commands. {-Preview | –Dsply| -Import | [securityKey=xxx]
-Clear[FID]} -aN|-a0,1,2|-aALL" storcli /cx/f(x|all) del|delete
[securityKey=xxx]
storcli /cx/f(x|all) import
[preview] [securityKey=xxx]"
Table 18 Security Commands
Set the key ID for the controller. MegaCli -CreateSecurityKey storcli /cx set SecurityKey=XXXXXX
-SecurityKey sssss | [passphrase=yyyyy] [keyId=zzzz]
[-Passphrase sssss] |
[-KeyID kkkkk] -aN
Change the security key for the MegaCli -ChangeSecurityKey storcli /cx set SecurityKey=XXXXXX
controller. -OldSecurityKey sssss | OldSecurityKey=yyyyy
-SecurityKey sssss|
[-Passphrase sssss] |
[-KeyID kkkkk] -aN
Compare and verify the security key MegaCli -VerifySecurityKey storcli /cx compare
for the controller. -SecurityKey sssss -aN SecurityKey=xxxxxx
Delete the security key. MegaCLI -DestroySecurityKey | storcli /cx delete SecurityKey
[-Force] -aN
Set the security key for the controller. MegaCli -SetKeyID -KeyID kkkkk storcli /cx set SecurityKey
-aN KeyId=xxxx
LSI Corporation
- 70 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Table 19 Virtual Drive Commands
Show the virtual drive information. MegaCli –LDInfo –Lx|-L0,1,2|-Lall storcli /cx/v(x|all) show
-aN|-a0,1,2|-aALL storcli /cx/v(x|all) show all
Set virtual drive properties. MegaCli –LDSetProp WT | WB|NORA |RA storcli /cx/v(x|all) set
| ADRA|-Cached|Direct| wrcache=WT|WB|AWB
CachedBadBBU|NoCachedBadBBU} | storcli /cx/v(x|all) set
-RW|RO|Blocked | rdcache=RA|NoRA
{-Name nameString} | storcli /cx/v(x|all) set
-EnDskCache|DisDskCache –Lx| iopolicy=Cached|Direct
-L0,1,2|-Lall -aN|-a0,1,2|-aALL storcli /cx/v(x|all) set
accesspolicy=RW|RO|Blocked|RmvBlkd
storcli /cx/v(x|all) set
pdcache=On|Off|Default
storcli /cx/v(x|all) set
name=<NameString>
"
Set power-saving (dimmer switch) MegaCli -LDSetPowerPolicy -Default| storcli /cx/v(x|all) set
properties. -Automatic| -None| -Maximum| ds=Default|Auto|None|Max|MaxNoCache
-MaximumWithoutCaching
-Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
Show virtual drive expansion MegaCli -getLdExpansionInfo storcli /cx/v(x|all) show expansion
information. -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
Expand the virtual drive within the MegaCli -LdExpansion -pN storcli /cx/v(x|all) expand
existing array; also use if you replace -dontExpandArray -Lx|-L0,1,2|-Lall Size=<value> [expandarray]
the drives with larger drives, beyond -aN|-a0,1,2|-aALL
the size of the existing array.
Secure the virtual drive. MegaCLI --LDMakeSecure storcli /cx/vx set security=on
-Lx|-L0,1,2,...|-Lall –An
Show specific properties of virtual MegaCli –LDGetProp -Cache | -Access storcli /cx/vx show
drives. | -Name | -DskCache
-Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
Start virtual drive initialization. MegaCli –LDInit –Start [Fast|Full] storcli /cx/v(x|all) start
-Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL init[Full]
Stop a running virtual drive MegaCli –LDInit -Abort storcli /cx/v(x|all) stop init
initialization. -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
Show the initialization progress. MegaCli –LDInit –ShowProg storcli /cx/v(x|all) show init
-Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
Start a consistency check on an MegaCli –LDCC –Start storcli /cx/v(x|all) start cc[Force]
uninitialized virtual drive. –Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
Start, stop, suspend, resume, and MegaCli -LDCC -Start|-Abort| storcli /cx/v(x|all) start cc
show the progress of a consistency -Suspend|-Resume|-ShowProg| storcli /cx/v(x|all) stop cc
check operation. -ProgDsply -Lx|-L0,1,2|-LALL
storcli /cx/v(x|all) pause cc -aN|-a0,1,2|-aALL
storcli /cx/v(x|all) resume cc
storcli /cx/v(x|all) show cc
LSI Corporation
- 71 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Table 19 Virtual Drive Commands (Continued)
Enable/disable automatic MegaCLI -LDBI -Enbl|-Dsbl| storcli /cx/v(x|all) set
background initialization. Show, stop, -getSetting|-Abort|-Suspend| autobgi=On|Off
pause, resume, and show the -Resume|-ShowProg|-ProgDsply storcli /cx/v(x|all) show autobgi
progress of the background -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-Aall
storcli /cx/v(x|all) stop bgi initialization.
storcli /cx/v(x|all) pause bgi
storcli /cx/v(x|all) resume bgi
storcli /cx/v(x|all) show bgi
Start and show progress for a migrate MegaCli –LDRecon {–Start –Rx [Add storcli /cx/vx start migrate
operation. | Rmv PhysDrv[E0:S0,E1:S1,...] ] } type=raidx [option=add|remove
| –ShowProg|-ProgDsply –Lx –aN drives=[e:]s|[e:]s-x|[e:]s-x,y]
[Force]
storcli /cx/v(x|all) show migrate
Delete preserved cache. MegaCLI -DiscardPreservedCache storcli /cx/v(x|all) delete
-Lx|-L0,1,2|-Lall -force preservedcache[force]
-aN|-a0,1,2|-aALL
Assign the CacheCade virtual drive. MegaCLI -Cachecade -assign|-remove storcli /cx/vx|all set
-Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL ssdCaching=on|off
Table 20 Physical Drive Commands
Description MegaCLI Command StorCLI Command
Show drive information. MegaCli -pdInfo - storcli /cx/ex/sx show
PhysDrv[E0:S0,E1:S1,...] storcli /cx/ex/sx show all
-aN|-a0,1,2|-aALL
Start, stop, pause, resume, or show MegaCLI PDRbld -Start|-Stop storcli /cx/ex/sx start rebuild
the progress of a rebuild operation. |-Suspend|-Resume|-ShowProg storcli /cx/ex/sx stop rebuild
|-ProgDsply -PhysDrv
storcli /cx/ex/sx pause rebuild [E0:S0,E1:S1,...]
-aN|-a0,1,2|-aALL storcli /cx/ex/sx resume rebuild
storcli /cx/ex/sx show rebuild
Start, stop, pause, resume, or show MegaCLI PDCpyBk -Start|-Stop storcli /cx/ex/sx start copyback
the progress of a copyback operation. |-Suspend|-Resume|-ShowProg target=exx:sxx
|-ProgDsply -PhysDrv storcli /cx/ex/sx stop copyback
[E0:S0,E1:S1,...]
storcli /cx/ex/sx pause copyback -aN|-a0,1,2|-aALL
storcli /cx/ex/sx resume copyback
storcli /cx/ex/sx show copyback
Mark a drive as missing. MegaCli -PdMarkMissing storcli /cx/ex/sx set missing
-physdrv[E0:S0,E1:S1,...]
-aN|-a0,1,2|-aALL
Show missing drive information. MegaCli -PdGetMissing storcli /cx/ex/sx show all
-aN|-a0,1,2|-aALL
NOTE This information is shown as part of the show all
command.
Replace the configured drive that is MegaCli -PdReplaceMissing storcli /cx/ex/sx insert array=x row=y
identified as missing, and then start -physdrv[E0:S0] -arrayA, -rowB
an automatic rebuild. -aN
Set the drive state to online MegaCli –PDOnline - storcli /cx/ex/sx set online
PhysDrv[E0:S0,E1:S1....]
-aN|-a0,1,2
LSI Corporation
- 72 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Table 20 Physical Drive Commands (Continued)
Description MegaCLI Command StorCLI Command
Set the drive state to offline. MegaCli –PDOffline storcli /cx/ex/sx set offline
-PhysDrv[E0:S0,E1:S1....]
-aN|-a0,1,2|-aALL
Set the drive state to JBOD MegaCli –PDMakeGood storcli /cx/ex/sx set good [force]
-PhysDrv[E0:S0,E1:S1....]
-aN|-a0,1,2|-aALL
Set the drive state to JBOD MegaCli -PDMakeJBOD storcli /cx/ex/sx set jbod
-PhysDrv[E0:S0,E1:S1,...]
-aN|-a0,1,2|-aALL
Add and delete hot spare drives. MegaCli –PDHSP {–Set storcli /cx/ex/sx add hotsparedrive
[{-Dedicated -ArrayN | [dgs=<N|0,1,2..>] enclaffinity
-Array0,1...}] [-EnclAffinity] nonrevertible
[-nonRevertible] } | storcli /cx/ex/sx delete hotsparedrive
-Rmv -PhysDrv[E0:S0,E1:S1,...]
-aN|-a0,1,2|-aALL
Start, stop, pause, resume or show MegaCli –PDClear -Start |-Stop| storcli /cx/ex/sx start initialization
the progress of an initialization -ShowProg |-ProgDsply storcli /cx/ex/sx stop initialization
process. - PhysDrv[E0:S0,E1:S1....]
storcli /cx/ex/sx pause initialization -aN|-a0,1,2|-aALL
storcli /cx/ex/sx resume initialization
storcli /cx/ex/sx show initialization
Start a drive locate and activate the MegaCli –PDLocate {[-start] | storcli /cx/ex/sx start locate
drive’s LED or stop a drive locate and -stop} -physdrv[E0:S0,E1:S1,...] storcli /cx/ex/sx stop locate
deactivate the drive’s LED. -aN|-a0,1,2|-aALL
Spin down an unconfigured drive MegaCli –PDPrpRmv [-Undo] storcli /cx/ex/sx spindown
and prepare it for removal or spin up – PhysDrv[E0:S0,E1:S1....] storcli /cx/ex/sx spinup.
spun-down drive and mark the drive -aN|-a0,1,2|-aALL
state as unconfigured good.
Show physical drive information of all MegaCli –PDList storcli /cx/eall/sall show [all]
connected drives. -aN|-a0,1..|-aAll
NOTE This command does not show drives whose
enclosure device ID is not available.
Flash the physical drive firmware. MegaCLI PdFwDownload[offline] storcli /cx[/ex]/sx download
[ForceActivate] {[-SataBridge] src=<filepath> [satabridge]
-PhysDrv[0:1]}|{-EncdevId[devId1 storcli /cx/ex download src=<filepath>
]} -f <filename> [forceActivate]
-aN|-a0,1,2|-Aall
Erase the drive's security MegaCli -PDInstantSecureErase storcli /cx/ex/sx secureerase [force]
configuration and securely erase data -PhysDrv[E0:S0,E1:S1,...] |
on a drive. [-Force] -aN|-a0,1,2|-aALL
LSI Corporation
- 73 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Table 20 Physical Drive Commands (Continued)
Description MegaCLI Command StorCLI Command
Show the security key for secured MegaCli -GetKeyID storcli /cx/ex/sx show securitykey
physical drives [-PhysDrv[E0:S0]] -aN keyid
Start, stop, and show the progress of MegaCli -SecureErase Start[ storcli /cx[/ex]/sx start erase
a secure erase operation Simple| [simple| normal| thorough]
[erasepatternA=<val>]\n[erasepatternB=< [Normal [ |ErasePattern
val>] ErasePatternA|ErasePattern
ErasePatternA ErasePattern Examples:
ErasePatternB]]|[Thorough [ storcli /cx/ex/sx start erase simple
|ErasePattern
storcli /cx/ex/sx start erase normal ErasePatternA|ErasePattern
erasepatterna=10101010 ErasePatternA ErasePattern
ErasePatternB]]] storcli /cx/ex/sx start erase thorough
erasepatterna=10101010 | Stop| ShowProg| ProgDsply
erasepatternb=10101111
[-PhysDrv [E0:S0,E1:S1,...] |
storcli /cx/ex/sx stop erase -Lx|-L0,1,2|-LALL]
-aN|-a0,1,2|-aALL
Enable/disable the direct physical MegaCLI DirectPdMapping storcli /cx set directpdmapping=<on |
drive mapping mode. -Enbl|-Dsbl|-Dsply off>
-aN|-a0,1,2|-Aall storcli /cx show directpdmappingShow the current state of the direct
physical drive mapping.
Table 21 Enclosure Commands
Description MegaCLI Command StorCLI Command
Show enclosure information. MegaCli –EncInfo storcli /cx/ex show
-aN|-a0,1,2|-aALL storcli /cx/ex show all
Show enclosure status. MegaCli –EncStatus storcli /cx/ex show status
-aN|-a0,1,2|-aALL
Table 22 PHY Commands
Description MegaCLI Command StorCLI Command
Show PHY information. MegaCli –PHYInfo -phyM storcli /cx/px(x|all) show
-aN|-a0,1,2|-aALL storcli /cx/px(x|all) show all
Set PHY link speed. MegaCLI PhySetLinkSpeed -phyM storcli /cx/px(x|all) set
-speed -aN|-a0,1,2|-aALL linkspeed=0(auto)|1.5|3|6|12
Show the PHY error counters. Megacli PhyErrorCounters -An storcli /cx/px(x|all) show
storcli /cx/px(x|all) show all
LSI Corporation
- 74 -
StorCLI Reference Manual Appendix B: MegaCLI Commands to StorCLI Command Conversion
January 2013
Table 23 Alarm Commands
Description MegaCLI Command StorCLI Command
Show alarm properties. MegaCli -AdpGetProp AlarmDsply storcli /cx(x|all) show alarm
-aN|-a0,1,2|-aALL
Set alarm properties. MegaCli -AdpSetProp AlarmEnbl | storcli /cx(x|all) set
AlarmDsbl | AlarmSilence alarm=<on|off|silence>
-aN|-a0,1,2|-aALL
Table 24 Event Log Properties Commands
Description MegaCLI Command StorCLI Command
Show event logs. MegaCli -AdpEventLog storcli /cx show eventloginfo
-GetEventLogInfo
-aN|-a0,1,2|-aALL
Show the specified type of event MegaCli -AdpEventLog -GetEvents storcli /cx show events [[type=
logs. {-info -warning -critical <sincereboot| sinceshutdown|
-fatal} {-f <fileName>} includedeleted|latest=x| ccincon
-aN|-a0,1,2|-aALL vd=<0,1,...>] filter=<info| warning|
critical|fatal>] file=<filepath>
Show the specified event logs. MegaCli -AdpEventLog storcli /cx show events
-GetSinceShutdown {-info [type=[latest=x|ccincon
-warning -critical -fatal} vd=|[sincereboot|sinceshutdown|included
{-f <fileName>} eleted|latest|ccincon]]]
-aN|-a0,1,2|-aALL [filter=[info|warning|critical|fatal]]
file=xyz.txt
Delete the event logs. MegaCli -AdpEventLog -Clear storcli /cx delete events
-aN|-a0,1,2|-aALL
Table 25 Premium Feature Key Commands
Description MegaCLI Command StorCLI Command
Show the Safe ID of the controller. MegaCli -ELF -GetSafeId -a0 storcli /cx(x|all) show safeid
Show the Advanced Software MegaCli -ELF –ControllerFeatures storcli /cx(x|all) show all
Options that are enabled on the -a0
controller, including the ones in trial NOTE This information shows as part of the controller
mode. show all.
Apply the Activation Key in preview MegaCli -ELF -Applykey key –val storcli /cx(x|all) set aso key=<key
mode. -preview -a0 value> preview
Apply the Activation Key. MegaCli -ELF -Applykey key –val storcli /cx(x|all) set aso key=<key
-a0 value>
Deactivate the trial key. MegaCli -ELF storcli /cx(x|all) set aso
–DeactivateTrialKey -a0 deactivatetrialkey
Show the re-host information and, if MegaCli -ELF -ReHostInfo -a0 storcli /cx(x|all) show rehostinfo
re-hosting is necessary, show the
controller and key vault serial
numbers.
Indicate to the controller that the MegaCli -ELF -ReHostComplete -a0 storcli /cx(x|all) set aso
re-host is complete. rehostcomplete
LSI Corporation
- 75 -
StorCLI Reference Manual Appendix C: Unsupported Commands in Embedded MegaRAID
January 2013
Appendix C: Unsupported Commands in Embedded MegaRAID
The commands in the following table are not supported in Embedded MegaRAID.
Table 26 Unsupported Commands in Embedded MegaRAID
Command Group Command
Jbod storcli /c0 set jbod=<on|off>
storcli /c0/s2 set jbod
storcli /c0/s2 set bootdrive=<on|off>
DS storcli /cx(x|all) set ds=OFF type=1|2|3|4
storcli /cx(x|all) set ds=ON type=1|2 [properties]
storcli /cx(x|all) set ds=ON type=3|4 DefaultLdType=<val> [properties]
storcli /cx(x|all) set ds [properties]
storcli /cx/v(x|all) set ds=Default|Auto|None|Max|MaxNoCache
Security storcli /cx delete securitykey
storcli /cx set securitykey=xx {passphrase=xxxx} {keyid=xxx}
storcli /cx set securitykey keyid=xxx
storcli /cx compare securitykey=xxxx
storcli /cx set securitykey=xx oldsecuritykey=xx
ASO storcli /cx(x|all) set aso key=<key value> preview
storcli /cx(x|all) set aso key=<key value>
storcli /cx(x|all) set aso transfertovault
storcli /cx(x|all) set aso rehostcomplete
storcli /cx(x|all) set aso deactivatetrialkey
storcli /cx(x|all) show safeid
storcli /cx(x|all) show rehostinfo
storcli /c0 set time =<yyyymmdd hh:mm:ss | system>
storcli /c0 show cc|consistencycheck
storcli /c0/vall show expansion
storcli /c0 set jbod
storcli /cx download src=<filepath> [forceActivate]
Copy back storcli /cx[/ex]/sx show copyback
storcli /cx[/ex]/sx start copyback target=eID:sID
storcli /cx[/ex]/sx stop copyback
storcli /cx[/ex]/sx pause copyback
storcli /cx[/ex]/sx resume copyback
Migrate storcli /cx/v(x|all) show migrate
storcli /cx/vx start migrate type=raidx [option=add|remove
drives=[e:]s|[e:]s-x|[e:]s-x,y] [Force]
Cache storcli /cx/v(x|all) set ssdcaching=on|off
storcli /cx(x|all) show preservedcache
storcli /cx/v(x|all) delete preservedcache[force]
LSI Corporation
- 76 -
StorCLI Reference Manual Appendix C: Unsupported Commands in Embedded MegaRAID
January 2013
Table 26 Unsupported Commands in Embedded MegaRAID (Continued)
Command Group Command
BBU storcli /cx/bbu show
storcli /cx/bbu show all
storcli /cx/bbu set [ learnDelayInterval=<val> | bbuMode=<val>
storcli /cx/bbu start learn
Secure ease storcli /cx/sx secureerase [force]
storcli /cx/sx start erase [simple| normal|
thorough][erasepatternA=<val>]
storcli /cx/sx stop erase
storcli /cx/sx show erase
Consistency check storcli /cx show cc/ConsistencyCheck
Controller storcli /cx show cc
LSI Corporation
- 77 -
StorCLI Reference Manual Appendix D: Revision Information
January 2013
Appendix D: Revision Information
Version and Date Description of Changes
Rev. E, December 2012 Added a new note in Section 4.2.2, storcli /cx show all.
Updated the commands for add virtual drive and updated the example. in Section 4.4.1, Add Virtual
Drives Commands.
Updated command syntax in Section 4.4.5, Change Virtual Drive Properties Commands.
Updated command syntax in Section 4.4.10, Background Initialization Commands.
Updated command syntax iand added a note in Section 4.5, Foreign Configurations Commands.
Updated command syntax in Section 4.11, PHY Commands.
Removed the stoponerror property name and updated the syntax for directpdmapping in
Table 2, Controller Commands.
Updated the syntax for linkspeed command in Table 10, Miscellaneous Commands
Removed the stoponerror property name from Table 12, Controller Commands.
Updated syntax for storcli /cx set directmapping command in Table 12, Controller
Commands.
Updated the syntax for show events command in Table 24, Event Log Properties Commands.
Rev. D, November 2012 Added the following sections:
Section 2.4, Installing StorCLI on FreeBSD Operating Systems.
Section 2.5, Installing StorCLI on the Microsoft EFI.
Section 2.6, Installing StorCLI on Solaris Operating Systems.
Added two notes in Chapter 3, StorCLI Command Syntax.
Updated Object Identifier in Table 1, Object Identifiers in the StorCli Command Syntax.
Added import and expand verbs in Table 2, Verbs in the StorCli Command Syntax.
Removed the storcli /cx show stoponerror command and added the storcli /cx set
termlog[=on|off|offthisboot] command in Section 4.2.1, Show and Set Controller
Properties Commands.
Updated descriptions for the off and delay options in Table 6, Set CC Input Options.
Updated a note in Section 4.3.1, Drive Show Commands.
Added new commands and a new note in Section 4.3.2, Missing Drives Commands.
Removed cc from Section 4.4.1, Add Virtual Drives Commands.
Replaced cc with cachecade in storcli /cx/vx|vall del cachecade in Section 4.4.2, Delete Virtual Drives
Commands.
Replaced cc with cachecade in Section 4.7.1, Drive Group Show.
Removed cc from storcli /cx/dall show cachecade in Section 4.7.1, Drive Group Show.
Added new commands in Section 4.4.11, Virtual Drive Expansion Commands.
Updated Section 5.5, Adding Virtual Drives.
Removed the stoponerror property name from Table 2, Controller Commands in Appendix A,
3Ware CLI Commands to StorCLI Command Conversion.
Removed the stoponerror property name from Table 12, Controller Commands in Appendix B,
MegaCLI Commands to StorCLI Command Conversion.
Rev. C, November 2012 Updated the ’/cx add/’ syntax in Section 4.4.1, Add Virtual Drives Commands.
Updated the description for force option in Section 4.4.2, Delete Virtual Drives Commands.
Updated the ’/cx add/’ syntax in the following tables:
Table 6, Virtual Drive Commands
Table 17, RAID Configuration Commands
LSI Corporation
- 78 -
StorCLI Reference Manual Appendix D: Revision Information
January 2013
Version and Date Description of Changes
Rev. B, September 2012 Updated the following sections:
Section 1.1, Overview.
Section 1.3, Devices Supported by the StorCLI Tool.
Chapter 2, Installation.
Section 2.2, Installing StorCLI on Linux Operating Systems.
Section 2.3, Installing StorCLI on VMware Operating Systems.
Section 4.2.1, Show and Set Controller Properties Commands.
Section 4.2.3.2, Patrol Read.
Section 4.2.3.3, Consistency Check.
Section 4.2.6, Flashing Controller Firmware Command.
Section 4.4.1, Add Virtual Drives Commands.
Section 4.4.8, Virtual Drive Migration Commands.
Section 4.9, BBU Commands.
Added a new verb in Table 2, Verbs in the StorCli Command Syntax.
Added a note in Chapter 4, Working with the Storage Command Line Tool.
Updated the Appendix A, 3Ware CLI Commands to StorCLI Command Conversion.
Updated the Appendix B, MegaCLI Commands to StorCLI Command Conversion.
Added a new Appendix C, Unsupported Commands in Embedded MegaRAID
Version 1.0 (Rev A.), May 2012 Initial release of the document.
LSI Corporation
- 79 -
